參數資料
型號： MC80C0216
廠商： Electronic Theatre Controls, Inc.
元件分類： 8位微控制器
英文描述： 8-BIT SINGLE-CHIP MICROCONTROLLERS
中文描述： 8位單晶片微控制器
文件頁數： 103/128頁
文件大小： 1408K
代理商： MC80C0216
Preliminary
MC80F0208/16/24
MAR. 2005 Ver 0.2
99
Figure 21-6 Timing of STOP Mode Release by Reset
21.3 Stop Mode at Internal RC-Oscillated Watchdog Timer Mode
In the Internal RC-Oscillated Watchdog Timer mode, the on-chip
oscillator is stopped. But internal RC oscillation circuit is oscil-
lated in this mode. The on-chip RAM and Control registers are
held. The port pins out the values held by their respective port
data register, port direction registers.
The Internal RC-Oscillated Watchdog Timer mode is activated
by execution of STOP instruction after setting the bit RCWDT of
CKCTLR to "1". (This register should be written by byte opera-
tion. If this register is set by bit manipulation instruction, for ex-
ample "set1" or "clr1" instruction, it may be undesired operation)
Note:
Caution: After STOP instruction, at least two or more
NOP instruction should be written
Ex)
LDM WDTR,#1111_1111B
LDM CKCTLR,#0010_1110B
LDM SSCR,#0101_1010B
STOP
NOP ;for stabilization time
NOP ;for stabilization time
The exit from Internal RC-Oscillated Watchdog Timer mode is
hardware reset or external interrupt or watchdog timer interrupt
(at RC-watchdog timer mode). Reset re-defines all the Control
registers but does not change the on-chip RAM. External inter-
rupts allow both on-chip RAM and Control registers to retain
their values.
If I-flag = 1, the normal interrupt response takes place. In this
case, if the bit WDTON of CKCTLR is set to "0" and the bit
WDTE of IENH is set to "1", the device will execute the watch-
dog timer interrupt service routine(Figure 8-6). However, if the
bit WDTON of CKCTLR is set to "1", the device will generate
the internal Reset signal and execute the reset processing(Figure
21-8). If I-flag = 0, the chip will resume execution starting with
the instruction following the STOP instruction. It will not vector
to interrupt service routine.(refer to Figure 21-4)
When exit from Stop mode at Internal RC-Oscillated Watchdog
Timer mode by external interrupt, the oscillation stabilization
time is required to normal operation. Figure 21-7 shows the tim-
ing diagram. When release the Internal RC-Oscillated Watchdog
Timer mode, the basic interval timer is activated on wake-up. It
is increased from 00
H
until FF
H
. The count overflow is set to start
normal operation. Therefore, before STOP instruction, user must
be set its relevant prescaler divide ratio to have long enough time
(more than 20msec). This guarantees that oscillator has started
and stabilized. By reset, exit from internal RC-Oscillated Watch-
dog Timer mode is shown in Figure 21-8.
~
STOP Mode
Time can not be control by software
Oscillator
(XI pin)
~
~
~
STOP Instruction Execution
Stabilization Time
t
ST
= 65.5mS @4MHz
Internal
Clock
Internal
RESET
~
~
~
~
~
RESET
相關PDF資料
PDF描述
MC80C0216K 8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80C0216Q 8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80C0224 8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80C0224K 8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80C0224Q 8-BIT SINGLE-CHIP MICROCONTROLLERS
相關代理商/技術參數
參數描述
MC80C0216K 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80C0216Q 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80C0224 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80C0224K 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80C0224Q 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*