- 您現在的位置：買賣IC網 > PDF目錄371048 > MC68HCP11A1CFN2 (MOTOROLA INC) HCMOS Single-Chip Microcontroller PDF資料下載
參數資料
| 型號： | MC68HCP11A1CFN2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HCMOS Single-Chip Microcontroller |
| 中文描述： | 8-BIT, 2 MHz, MICROCONTROLLER, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 30/158頁 |
| 文件大?。?/td> | 776K |
| 代理商： | MC68HCP11A1CFN2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
MOTOROLA
3-4
ON-CHIP MEMORY
MC68HC11A8
TECHNICAL DATA
3
In expanded multiplexed operating modes, memory locations are basically the same
as the single- chip operating modes; however, the locations between the shaded ar-
eas (designated EXT) are for externally addressed memory and l/O. If an external
memory or l/O device is located to overlap an enabled internal resource, the internal
resource will take priority. For reads of such an address the data (if any) driving the
port C data inputs is ignored and will not result in any harmful conflict with the internal
read. For writes to such an address data is driven out of the port C data pins as well
as to the internal location. No external devices should drive port C during write access-
es to internal locations; however, there is normally no conflict since the external ad-
dress decode and/ or data direction control should incorporate the R/W signal in their
development. The R/W, AS, address, and write data signals are valid for all accesses
including accesses to internal memory and registers.
The special bootstrap operating mode memory locations are similar to the single-chip
operating mode memory locations except that a bootstrap program at memory loca-
tions $BF40 through $BFFF is enabled. The reset and interrupt vectors are addressed
at $BFC0–$BFFF while in the special bootstrap operating mode. These vector ad-
dresses are within the 192 byte memory used for the bootstrap program.
The special test operating mode memory map is the same as the expanded multi-
plexed operating mode memory map except that the reset and interrupt vectors are
located at external memory locations $BFC0–$BFFF.
3.2 RAM and I/O Mapping Register (INIT)
There are 64 internal registers which are used to control the operation of the MCU.
These registers can be relocated on 4K boundaries within the memory space, using
the INIT register. Refer to
Table 3-1
for a complete list of the registers. The registers
and control bits are explained throughout this document.
The INIT register is a special-purpose 8-bit register which may be used during initial-
ization to change the default locations of RAM and control registers within the MCU
memory map. It may be written to only once within the initial 64 E clock cycles after a
reset and thereafter becomes a read-only register.
The default starting address for internal RAM is $0000 and the default starting address
for the 64 control registers is $1000 (the INIT register is set to $01 at reset). The upper
four bits of the INIT register specify the starting address for the 256 byte RAM and the
lower four bits of INIT specify the starting address for the 64 control registers. These
four bits are matched to the upper four bits of the 16-bit address.
Throughout this document, the control register addresses will be displayed with the
high-order digit shown as a bold “
1
” to indicate that the register block may be relocated
to some 4K memory page other than its default position of $1000-$103F.
7
6
5
4
3
2
1
0
$
1
03D
RESET
RAM3
0
RAM2
0
RAM1
0
RAM0
0
REG3
0
REG2
0
REG1
0
REG0
1
INIT
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HCP11A1CFN3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1MFN2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1MP2 | HCMOS Single-Chip Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HCP11A1CFN3 | 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HCP11A1FN | 制造商:MOTORALA 功能描述: |
| MC68HCP11E0CP2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC68HCP11E0FN | 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HCP11E0FNE | 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。