參數資料
型號： MC68HC711K4CFN2
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT MICROCONTROLLER
中文描述： 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PQCC84
封裝： PLASTIC, LCC-84
文件頁數： 22/80頁
文件大小： 420K
代理商： MC68HC711K4CFN2
MOTOROLA
22
M68HC11 K Series
MC6HC11KTS/D
3.4 EEPROM
The 640-byte EEPROM is initially located at $0D80 after reset, assuming EEPROM is enabled in the
memory map by the EEON bit in the CONFIG register. EEPROM can be placed at any 4-Kbyte bound-
ary ($xD80) by writing appropriate values to the INIT2 register. Note that EEPROM can be mapped so
that it contains the vector space. Refer to
Figure 4
. The MC68HC11K0, MC68HC11K3, MC68L11K0,
and MC68L11K3 have no EEPROM. Refer to the
ordering information tables
.
Programming and erasing the EEPROM is controlled by the PPROG register, and dependent upon the
block protect (BPROT) register value. An on-chip charge pump develops the high voltage required for
programming and erasing. When the frequency of the E clock is less than 1 MHz, select the internal
clock source to drive the EEPROM charge pump by writing one to the CSEL bit in the OPTION register.
The CONFIG register consists of a single EEPROM byte. Although the byte is not included in the 640-
byte EEPROM array, programming the CONFIG register requires the same procedure as any byte in
the array. The erased state of bits in the CONFIG register is logic one. Refer to the CONFIG register
description that follows this section.
The erased state of an EEPROM byte is $FF (all ones).
To erase the EEPROM, ensure that the proper bits of the BPROT register are cleared, then complete
the following steps using the PPROG register:
1.
2.
Set the ERASE, EELAT, and appropriate BYTE and ROW bits in PPROG register.
Write to the appropriate EEPROM address with any data. Row erase only requires a write to
any location in the row. Bulk erase is done by writing to any location in the array.
Set the ERASE, EELAT, EEPGM, and appropriate BYTE and ROW bits in PPROG register.
Delay for 10 ms or more, as appropriate.
Clear the EEPGM bit in PPROG to turn off the programming voltage.
Clear the PPROG register to reconfigure the EEPROM address and data buses for normal op-
eration.
To program the EEPROM, ensure the proper bits of the BPROT register are cleared and use the
PPROG register to complete the following steps:
3.
4.
5.
6.
1.
2.
3.
4.
5.
6.
Set the EELAT bit in PPROG register.
Write data to the desired address.
Set EEPGM bit in PPROG.
Delay for 10 ms or more, as appropriate.
Clear the EEPGM bit in PPROG to turn off the programming voltage.
Clear the PPROG register to reconfigure the EEPROM address and data buses for normal op-
eration.
CAUTION
Since it is possible to perform other operations while the EEPROM programming/
erase operation is in progress, it is common to start the operation and then return
to the main program until the 10 ms is completed. When the EELAT bit is set at the
beginning of a program/erase operation, the EEPROM is electronically removed
from the memory map; thus, it is not accessible during the program/erase cycle.
Care must be taken to ensure that EEPROM resources will not be needed by any
routines in the code during the 10 ms program/erase time.
PPROG
—EEPROM Programming Control
$003B
Bit 7
6
5
4
3
2
1
Bit 0
ODD
EVEN
LVPI
BYTE
ROW
ERASE
EELAT
EEPGM
RESET:
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68HC11K4CFN2 Technical Summary 8-Bit Microcontroller
MC68HC11K4CFN3 Technical Summary 8-Bit Microcontroller
MC68HC11K1VFU2 8-BIT MICROCONTROLLER
MC68HC11K4VFU2 MNX Series Enclosure; NEMA Type:1, 2, 4, 4X, 6, 12, 13; Enclosure Material:Polycarbonate; External Height:5.1"; External Width:3"; External Depth:3.9"
MC68HC11K1VFU3 MNX Series Enclosure; NEMA Type:1, 2, 4, 4X, 6, 12, 13; Enclosure Material:Polycarbonate; External Height:10"; External Width:7.1"; External Depth:2.5"; Enclosure Color:Light Gray; Approval Bodies:UL, CSA; Cover Color:Light Gray RoHS Compliant: Yes
相關代理商/技術參數
參數描述
MC68HC711K4CFN4 功能描述:IC MCU 24K OTP 4MHZ 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC711K4CFNE3 制造商:Freescale Semiconductor 功能描述:
MC68HC711K4CFNE4 制造商:Freescale Semiconductor 功能描述:
MC68HC711K4CFU4 功能描述:IC MCU 24K 4MHZ EEPROM 80-QFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC711KS2CPU4 制造商:Motorola Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*