參數資料
型號： MC68HC705X4
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： HCMOS Microcontroller Unit
中文描述： HCMOS微控制器
文件頁數： 78/156頁
文件大?。?/td> 940K
代理商： MC68HC705X4
Motorola CAN
MC68HC05X4
Motorola CAN
NOTE:
When setting TIE while TCS or TBA is set, no interrupt will be requested.
Successful transmission must occur after setting the TIE bit to get an
interrupt flag.
RIE — Receive interrupt enable
1 = Enabled – The CPU will get an interrupt request whenever a
message has been received free of errors.
0 = Disabled – The CPU will get no receive interrupt request.
RR — Reset request
When the MCAN detects that RR has been set it aborts the current
transmission or reception of a message and enters the reset state. A
reset request may be generated by either an external reset or by the
CPU or by the MCAN. The RR bit can be cleared only by the CPU.
After the RR bit has been cleared, the MCAN will start normal
operation in one of two ways. If RR was generated by an external
reset or by the CPU, then the MCAN starts normal operation after the
first occurrence of 11 recessive bits. The MCAN module is not
synchronized to the bus until the 11 recessive bits have been
received. When the SLEEP bit is set during this non synchronous
state, an immediate wake-up wil be generated by the MCAN module.
If, however, the RR was generated by the MCAN due to the BS bit
being set (see
MCAN status register (CSTAT)
) the MCAN waits for
128 occurrences of 11 recessive bits before starting normal
operation.
A reset request should not be generated by the CPU during a
message transmission. Ensure that a message is not being
transmitted as follows:
if TCS in CSTAT is clear – set AT in CCOM (use STA or STX),
read CSTAT.
if TS in CSTAT is set – wait until TS is clear.
Note that a CPU-generated reset request does not change the values
in the transmit and receive error counters.
1 = Present – MCAN will be reset.
0 = Absent – MCAN will operate normally.
NOTE:
The following registers may only be accessed when reset request =
present: CACC, CACM, CBT0, CBT1, and COCNTRL.
10-mcan
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC68HC711A0FB ROM-based high-performance microcontrollers
MC68HC711Ex APPENDIX A ELECTRICAL CHARACTERISTICS
MC68HC711K4VFN2 8-BIT MICROCONTROLLER
MC68HC711K4VFN3 8-BIT MICROCONTROLLER
MC68HC711K4VFN4 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
MC68HC706P6ACDW 制造商:Motorola Inc 功能描述:
MC68HC708MP16CFU 制造商:MAJOR 功能描述:
MC68HC711D3CFBE2 制造商:Freescale Semiconductor 功能描述:
MC68HC711D3CFN2 功能描述:IC MCU 2MHZ 4K OTP 44-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC711D3CFNE2 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*