參數資料
型號: MC68HC705X4
廠商: 飛思卡爾半導體(中國)有限公司
英文描述: HCMOS Microcontroller Unit
中文描述: HCMOS微控制器
文件頁數: 51/156頁
文件大?。?/td> 940K
代理商: MC68HC705X4
Resets, Interrupts and Low Power Modes
Interrupts
MC68HC05X4 Rev 1.0
Resets, Interrupts and Low Power Modes
For More Information On This Product,
Go to: www.freescale.com
5-resets
Maskable
hardware
interrupts
If the interrupt mask bit (I-bit) of the CCR is set, all maskable interrupts
(internal and external) are masked. Clearing the I-bit allows interrupt
processing to occur.
NOTE:
The internal interrupt latch is cleared in the first part of the interrupt
service routine; therefore, one external interrupt pulse could be latched
and serviced as soon as the I-bit is cleared.
MCAN interrupt
(CIRQ)
Several sources can trigger a CIRQ. The MCAN interrupt register at
$0023 is used to identify the source. Each CIRQ source can be
individually enabled (except the wake-up interrupt, which is always
enabled) by different bits of the MCAN control register at $0020.
The CIRQ sources are (see also
MCAN interrupt register (CINT)
):
Receive IRQ: this signals successful reception of a complete message,
Transmit IRQ: this signals successful transmission of a complete
message,
Error IRQ: this is set when either the error status or bus status bits in the
MCAN status register change state (see
MCAN status register
(CSTAT)
),
Data Overrun: an incoming message on the bus cannot be received
because both receive buffers are tied up,
Wake-up IRQ: this signals activity on the bus while the MCAN is in
SLEEP mode.
CIRQ interrupts are serviced by the routine located at the address
specified by the contents of $1FFA and $1FFB.
Wired-OR
interrupt (WOI)
An external WOI capability is provided on all I/O pins. When WOI is
enabled on a given pin (refer to
Input/output programming
and
Port
A
), an external interrupt is requested when this pin is pulled high. The
interrupt request is latched immediately following the rising edge of the
external WOI interrupt signal. It is then synchronised internally and
serviced by the interrupt routine whose start address is contained in
memory locations $1FF6 and $1FF7. The address of the latch bit for the
F
Freescale Semiconductor, Inc.
n
.
相關PDF資料
PDF描述
MC68HC711A0FB ROM-based high-performance microcontrollers
MC68HC711Ex APPENDIX A ELECTRICAL CHARACTERISTICS
MC68HC711K4VFN2 8-BIT MICROCONTROLLER
MC68HC711K4VFN3 8-BIT MICROCONTROLLER
MC68HC711K4VFN4 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
MC68HC706P6ACDW 制造商:Motorola Inc 功能描述:
MC68HC708MP16CFU 制造商:MAJOR 功能描述:
MC68HC711D3CFBE2 制造商:Freescale Semiconductor 功能描述:
MC68HC711D3CFN2 功能描述:IC MCU 2MHZ 4K OTP 44-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C,IrDA,LIN,SPI,UART/USART 外圍設備:DMA,PDR,POR,PVD,PWM,溫度傳感器,WDT 輸入/輸出數:26 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN,36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC711D3CFNE2 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT