參數資料
型號： MC68HC705P6ACP
廠商： Freescale Semiconductor
文件頁數： 53/98頁
文件大?。?/td> 0K
描述： IC MCU 2.1MHZ 4.5K OTP 28-DIP
標準包裝： 13
系列： HC05
核心處理器： HC05
芯體尺寸： 8-位
速度： 2.1MHz
連通性： SIO
外圍設備： POR，WDT
輸入/輸出數： 21
程序存儲器容量： 4.5KB（4.5K x 8）
程序存儲器類型： OTP
RAM 容量： 176 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
數據轉換器： A/D 4x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-DIP（0.600"，15.24mm）
包裝： 管件
MC68HC705P6A Advance Information Data Sheet, Rev. 2.1
Freescale Semiconductor
57
Chapter 10
EPROM
10.1 Introduction
The user EPROM consists of 48 bytes of user page zero EPROM from $0020 to $004F, 4608 bytes of
user EPROM from $0100 to $12FF, the two MOR reset values located at $1EFF and $1F00, and 16 bytes
of user vectors EPROM from $1FF0 to $1FFF. The bootloader ROM and vectors are located from $1F01
to $1FEF.
10.2 EPROM Erasing
NOTE
Only parts packaged in a windowed package may be erased. Others are
one-time programmable and may not be erased by UV exposure.
The MC68HC705P6A can be erased by exposure to a high-intensity ultraviolet (UV) light with a
wavelength of 2537 angstroms. The recommended dose (UV intensity multiplied by exposure time) is
15 Ws/cm2. UV lamps without shortwave filters should be used, and the EPROM device should be
positioned about one inch from the UV lamp. An erased EPROM byte will read as $00.
10.3 EPROM Programming Sequence
The bootloader software goes through a complete write cycle of the EPROM including the MOR. This is
followed by a verify cycle which continually branches in a loop if an error is found. A sample routine to
program a byte of EPROM is shown in Table 10-1.
NOTE
To avoid damage to the MCU, VDD must be applied to the MCU before VPP.
10.4 EPROM Registers
Three registers are associated with the EPROM: the EPROM programming register (EPROG) and the
two mask option registers (MOR). The EPROG register controls the actual programming of the EPROM
bytes and the MOR. The MOR registers control the six mask options found on the ROM version of this
MCU (MC68HC05P6), the EPROM security feature, and eight additional port A interrupt options.
10.5 EPROM Programming Register (EPROG)
This register is used to program the EPROM array. Only the ELAT and EPGM bits are available.
Table 10-1 shows the location of each bit in the EPROG register and the state of these bits coming out of
reset. All the bits in the EPROG register are cleared by reset.
相關PDF資料
PDF描述
MC68HC705SR3CPE IC MCU 3.75K 2.1MHZ OTP 40-DIP
MC68HC711D3CFN2 IC MCU 2MHZ 4K OTP 44-PLCC
MC68HC908GT8CFB IC MCU 8K FLASH 8MHZ 44-QFP
MC68HC908JL3ECFA IC MCU 4K FLASH 8MHZ 48-LQFP
MC68HC908QT2CFQ MCU 8-BIT 1.5KB FLASH 8-DFN
相關代理商/技術參數
參數描述
MC68HC705P6ADW 制造商:Rochester Electronics LLC 功能描述:MCU, 176 BYTES RAM, A/D - Bulk
MC68HC705P6AMDW 功能描述:IC MCU 4.6K OTP 2.1MHZ 28-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC05 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC705P6AMP 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705P6CDW 制造商:Motorola Inc 功能描述:
MC68HC705P6CP 制造商:Freescale Semiconductor 功能描述: 制造商:Motorola Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*