參數資料
型號： MC68HC11F1MFN3
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 98/162頁
文件大?。?/td> 4554K
代理商： MC68HC11F1MFN3
OPERATING MODES AND ON-CHIP MEMORY
MC68HC11F1
4-2
TECHNICAL DATA
The bootstrap ROM contains a small program which initializes the SCI and allows the
user to download a program of up to 1024 bytes into on-chip RAM. After a four-char-
acter delay, or after receiving the character for address $03FF, control passes to the
loaded program at $0000. An external pull-up resistor is required when using the SCI
transmitter pin (TxD) because port D pins are configured for wired-OR operation by
the bootloader. In bootstrap mode, the interrupt vectors point to RAM. This allows the
use of interrupts through a jump table. Refer to Motorola application note AN1060,
M68HC11 Bootstrap Mode.
4.2 On-Chip Memory
The MC68HC11F1 contains 1024 bytes of on-chip RAM and 512 bytes of EEPROM.
The bootloader ROM occupies 256 bytes. The CONFIG register is implemented as a
separate EEPROM byte.
4.2.1 Mapping Allocations
Memory locations for on-chip resources are the same for both expanded and single-
chip modes. The 96-byte register block originates at $1000 after reset and can be
placed at any other 4-Kbyte boundary ($x000) after reset by writing an appropriate val-
ue to the INIT register. Refer to Figure 4-1, which illustrates the memory map.
The on-board 1024-byte RAM is initially located at $0000 after reset. If RAM and reg-
isters are both mapped to the same 4-Kbyte boundary, the first 96 bytes of RAM are
inaccessible (registers have higher priority). Remapping is accomplished by writing
appropriate values to the INIT register.
The 512-byte EEPROM array is initially located at $FE00 after reset when EEPROM
is enabled in the memory map by the CONFIG register. In expanded and special test
modes EEPROM can be placed at any other 4-Kbyte boundary ($xE00) by program-
ming bits EE[3:0] in the CONFIG register to an appropriate value. In single-chip and
bootstrap modes the EEPROM is forced on and cannot be remapped.
In special bootstrap mode, a bootloader ROM is enabled at locations $BF00–$BFFF.
The vectors for special bootstrap mode are contained in the bootloader program. The
boot ROM fills 256 bytes of the memory map even though not all locations are used.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HC11K3CFU2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP80
MC68HC11K3CFU4 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80
MC68HC11K3VFU3 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP80
MC68HC711K4CFS4 8-BIT, UVPROM, 4 MHz, MICROCONTROLLER, CQCC84
MC68L11K0FU3 8-BIT, 3 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
MC68HC11F1MFN4 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller
MC68HC11F1MFU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1MFU1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1MFU3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1MFU4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*