- 您現在的位置：買賣IC網 > PDF目錄69027 > MC68HC11D0CP2 (MOTOROLA INC) 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP40 PDF資料下載
參數資料
| 型號： | MC68HC11D0CP2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| 封裝： | PLASTIC, DIP-40 |
| 文件頁數： | 71/124頁 |
| 文件大小： | 1481K |
| 代理商： | MC68HC11D0CP2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
MOTOROLA
RESETS AND INTERRUPTS
MC68HC11D3
5-6
TECHNICAL DATA
5.2.7 COP
The COP watchdog system is enabled if the NOCOP control bit in the CONFIG regis-
ter is clear, and disabled if NOCOP is set. The COP rate is set for the shortest duration
time-out.
5.2.8 SCI
The reset condition of the SCI system is independent of the operating mode. At reset,
the SCI baud rate is indeterminate and must be established by a software write to the
BAUD register. All transmit and receive interrupts are masked and both the transmitter
and receiver are disabled so the port pins default to being general-purpose I/O lines.
The SCI frame format is initialized to an 8-bit character size. The send break and re-
ceiver wake-up functions are disabled. The TDRE and TC status bits in the SCI status
register are both set, indicating that there is no transmit data in either the transmit data
register or the transmit serial shift register. The RDRF, IDLE, OR, NF, and FE receive-
related status bits are cleared.
5.2.9 SPI
The SPI system is disabled by reset. The port pins associated with this function default
to being general-purpose I/O lines.
5.2.10 System
The memory system is configured for normal read operation. PSEL[3:0] are initialized
with the value $0101, causing the external IRQ pin to have the highest I-bit interrupt
priority. The IRQ pin is configured for level sensitive operation (for wired-OR systems).
The RBOOT, SMOD, and MDA bits in the HPRIO register reflect the status of the
MODB and MODA inputs at the rising edge of reset. The DLY control bit in OPTION is
set to specify that an oscillator start-up delay is imposed upon recovery from STOP.
The clock monitor system is disabled by CME equals zero.
5.3 Reset and Interrupt Priority
Resets and interrupts have a hardware priority that determines which reset or interrupt
is serviced first when simultaneous requests occur. Any maskable interrupt can be giv-
en priority over other maskable interrupts.
The first six interrupt sources are not maskable. The priority arrangement for these
sources is as follows:
1.
POR or RESET pin
2.
Clock monitor reset
3.
COP watchdog reset
4. XIRQ interrupt
5. Illegal opcode interrupt
6. Software interrupt (SWI)
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11D0CP2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC11D0CP | 8-BIT, MICROCONTROLLER, PDIP40 |
| MC68HC11L6CFU1 | 8-BIT, OTPROM, 1 MHz, MICROCONTROLLER, PQFP64 |
| MC68HC16S2CPU25 | 16-BIT, 25.17 MHz, MICROCONTROLLER, PQFP100 |
| MC16S2CPU20B1 | 16-BIT, 20.97 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11D0CP3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MC68HC11D0FB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MC68HC11D0FN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MC68HC11D0FNR2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MC68HC11D0P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。