參數資料
型號： MC68HC05BD5
廠商： Motorola, Inc.
英文描述： 8-Bit Microcontroller Units (MCU).(8位微控制器)
中文描述： 8位微控制器單元（MCU）。（8位微控制器）
文件頁數： 50/112頁
文件大小： 676K
代理商： MC68HC05BD5
MOTOROLA
7-4
MC68HC05BD3
M-BUS SERIAL INTERFACE
7
7.2.3
Data Transfer
Once a successful slave addressing is achieved, the data transfer can proceed byte by byte in a
direction specified by the R/W bit sent by the calling master.
Each data byte is 8 bits long. Data can be changed only when SCL is low and must be held stable
when SCL is high as shown in Figure 7-2. One clock pulse is for one bit of data transfer, MSB is
transferred first. Each data byte has to be followed by an acknowledge bit. Hence, one complete
data byte transfer requires 9 clock pulses.
If the slave receiver does not acknowledge the master, the SDA line should be left high by the
slave, the master can then generate a STOP signal to abort the data transfer or a START signal
(repeated START) to commence a new calling.
If the master receiver does not acknowledge the slave transmitter after one byte transmission, it
means an “end of data” to the slave. The slave shall release the SDA line for the master to
generate STOP or START signal.
7.2.4
Repeated START Signal
As shown in Figure 7-2, a repeated START signal is to generate a START signal without first
generating a STOP signal to terminate the communication. This is used by the master to
communicate with another slave or with the same slave in a different mode (transmit/receive
mode) without releasing the bus.
7.2.5
STOP Signal
The master can terminate the communication by generating a STOP signal to free the bus.
However, the master may generate a START signal followed by a calling command without
generating a STOP signal first. This is called repeat START. A STOP signal is defined as a low to
high transition of SDA while SCL is at a logical high; see Figure 7-2.
7.2.6
Arbitration Procedure
This interface circuit is a true multi-master system which allows more than one master to be
connected. If two or more masters try to control the bus at the same time, a clock synchronization
procedure determines the bus clock. The clock low period is equal to the longest clock low period
among the masters; and the clock high period is the shortest among the masters. A data
arbitration procedure determines the priority. A master will lose arbitration if it transmits a logic “1”
while the others transmit logic “0”, the losing master will immediately switch over to slave receive
mode and stops its data and clock outputs. The transition from master to slave mode will not
generate a STOP condition. Meanwhile, a software bit will be set by hardware to indicate loss of
arbitration.
TPG
相關PDF資料
PDF描述
MC68HC705BD3 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05C4 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05C5 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05C8A Microcontrollers
MC68HC05C9A 8-Bit Microcontroller(8位微控制器)
相關代理商/技術參數
參數描述
MC68HC05C0CP 制造商:Motorola Inc 功能描述:
MC68HC05C12 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS
MC68HC05C12B 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS
MC68HC05C12CP 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS
MC68HC05C12P 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*