參數資料
型號： MC68332VFC20
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 32-Bit Modular Microcontroller
中文描述： 32-BIT, 20 MHz, MICROCONTROLLER, PQFP132
封裝： PLASTIC, QFP-132
文件頁數： 54/88頁
文件大?。?/td> 446K
代理商： MC68332VFC20
MOTOROLA
54
MC68332
MC68332TS/D
5.1.7 Period Measurement with Missing Transition Detect (PMM)
Period measurement with missing transition detect allows a special-purpose 23-bit period measure-
ment. It detects the occurrence of a missing transition (caused by a missing tooth on the sensed wheel),
indicated by a period measurement that is greater than a programmable ratio of the previous period
measurement. Once detected, this condition can be counted and compared to a programmable number
of additional transitions detected before TCR2 is reset to $FFFF. In addition, one byte at an address
specified by a channel parameter can be read and used as a flag. A nonzero value of the flag indicates
that TCR2 is to be reset to $FFFF once the next missing transition is detected.
5.1.8 Position-Synchronized Pulse Generator (PSP)
Any channel of the TPU can generate an output transition or pulse, which is a projection in time based
on a reference period previously calculated on another channel. Both TCRs are used in this algorithm:
TCR1 is internally clocked, and TCR2 is clocked by a position indicator in the user's device. An example
of a TCR2 clock source is a sensor that detects special teeth on the flywheel of an automobile using
PMA or PMM. The teeth are placed at known degrees of engine rotation; hence, TCR2 is a coarse rep-
resentation of engine degrees, i.e., each count represents some number of degrees.
Up to 15 position-synchronized pulse generator function channels can operate with a single input ref-
erence channel executing a PMA or PMM input function. The input channel measures and stores the
time period between the flywheel teeth and resets TCR2 when the engine reaches a reference position.
The output channel uses the period calculated by the input channel to project output transitions at spe-
cific engine degrees. Because the flywheel teeth might be 30 or more degrees apart, a fractional multi-
plication operation resolves down to the desired degrees. Two modes of operation allow pulse length
to be determined either by angular position or by time.
5.1.9 Stepper Motor (SM)
The stepper motor control algorithm provides for linear acceleration and deceleration control of a step-
per motor with a programmable number of step rates of up to 14. Any group of channels, up to eight,
can be programmed to generate the control logic necessary to drive a stepper motor.
The time period between steps (P) is defined as:
P(r) = K1 – K2
r
where r is the current step rate (1–14), and K1 and K2 are supplied as parameters.
After providing the desired step position in a 16-bit parameter, the CPU issues a step request. Next, the
TPU steps the motor to the desired position through an acceleration/deceleration profile defined by pa-
rameters. The parameter indicating the desired position can be changed by the CPU while the TPU is
stepping the motor. This algorithm changes the control state every time a new step command is re-
ceived.
A 16-bit parameter initialized by the CPU for each channel defines the output state of the associated
pin. The bit pattern written by the CPU defines the method of stepping, such as full stepping or half step-
ping. With each transition, the 16-bit parameter rotates one bit. The period of each transition is defined
by the programmed step rate.
5.1.10 Period/Pulse-Width Accumulator (PPWA)
The period/pulse-width accumulator algorithm accumulates a 16-bit or 24-bit sum of either the period
or the pulse width of an input signal over a programmable number of periods or pulses (from 1 to 255).
After an accumulation period, the algorithm can generate a link to a sequential block of up to eight chan-
nels. The user specifies a starting channel of the block and number of channels within the block. Gen-
eration of links depends on the mode of operation. Any channel can be used to measure an
accumulated number of periods of an input signal. A maximum of 24 bits can be used for the accumu-
相關PDF資料
PDF描述
MC68340V 32-Bit Microprocessor(32位微處理器)
MC68341FT16 Integrated Processor Users Manual
MC68341FT16V Integrated Processor Users Manual
MC68341FT25 Integrated Processor Users Manual
MC68341UMAD Integrated Processor Users Manual
相關代理商/技術參數
參數描述
MC68332VFV16 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller
MC68332VFV20 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller
MC68334 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement
MC68334GCEH16 功能描述:IC MCU 16MHZ 2K RAM 132-PQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M683xx 標準包裝:1 系列:87C 核心處理器:MCS 51 芯體尺寸:8-位 速度:16MHz 連通性:SIO 外圍設備:- 輸入/輸出數:32 程序存儲器容量:8KB（8K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 6 V 數據轉換器:- 振蕩器型:外部 工作溫度:0°C ~ 70°C 封裝/外殼:44-DIP 包裝:管件 其它名稱:864285
MC68334GCEH16 制造商:Freescale Semiconductor 功能描述:Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*