- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33889 (飛思卡爾半導體(中國)有限公司) System Basis Chip (SBC) with Low Speed Fault Tolerant CAN Interface PDF資料下載
參數資料
| 型號： | MC33889 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | System Basis Chip (SBC) with Low Speed Fault Tolerant CAN Interface |
| 中文描述： | 帶有低速CAN的精簡版系統基礎芯片 |
| 文件頁數： | 14/30頁 |
| 文件大小： | 464K |
| 代理商： | MC33889 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
PC33889
14
PC33889
4.9.1
Wake up from wake up inputs (L0, L1) without cyclic sense:
The wake up lines are dedicated to sense external switches state and if changes occur to wake up the MCU (In sleep or stop
modes). The wake up pins are able to handle 40V DC. The internal threshold is 3V typical and these inputs can be used as input
port expander. The wake up inputs state can be read through SPI (register WUR). L0 has a lower threshold than L1 in order to
allow connection and wake up from a digital output such as a CAN physical interface for instance.
4.9.2
Cyclic sense wake up (Cyclic sense timer and wake up inputs L0, L1)
The SBC can wake up upon state change of one of the wake up input lines (L0, L1) while the external pull up or pull down
resistor of the switches associated to the wake up input lines are biased with HS1 Vsup switch. The HS1 switch is activated in
sleep or stop mode from an internal timer. Cyclic sense and Forced wake up are exclusive. If Cyclic Sense is enabled the forced
wake up can not be enabled.
4.9.3
Forced wake up
The SBC can wake up automatically after a pre determined time spent in sleep or stop mode. Forced wake up is enabled by
setting bit FWU in LPC register. Cyclic sense and Forced wake up are exclusive. If Forced wake up is enabled the Cyclic Sense
can not be enabled.
4.9.4
CAN wake up
The device can wake up from a CAN message. CAN wake up cannot be disabled.
4.9.5
SPI wake up
The device can wake up by the CSB pin in sleep or stop mode. Wake up is detected by CSB pin transition from low to high
level. In stop mode this correspond to the condition where MCU and SBC are both in Stop mode and when the application wake
up events come through the MCU.
4.9.6
System power up
At power up the device automatically wakes up.
4.10
SPI
The complete device control as well as the status report is done through a 8 bits SPI interface. Refer to SPI paragraph.
4.11
CAN
The device incorporates a low speed fault tolerant CAN physical interface. Speed rate is up to 125kBauds. Its electrical
parameters for the CANL, CANH, Rtl, Rth Rx and Tx pins are compatible with the MC33388D.
The state of the CAN interface is programmable through SPI.
4.12
Device power up, SBC wake up
After device or system power up or a wake up from sleep mode, the SBC enters into “reset mode” then into “normal request
mode”.
4.13
Battery fall early warning:
This function provides an Interrupt when the Vsup voltage is below 6.1V typical. This interrupt is maskable. An hysteresis is
included. Operation is only in Normal and Standby modes. Vbat low state reported in IOR register.
4.14
Package and thermal consideration
The device is proposed in a standard surface mount SO28 package. In order to improve the thermal performances of the
SO28 package, 8 pins are internally connected to the lead frame and are used for heat transfer to the printed circuit board.
4.15
Table 1: Reset and Wdogb operation
Figure below shows the reset and watchdog output operation. Reset is active at device power up and wake up. Reset is
activated in case of Vdd1 fall or watchdog not triggered. Wdogb output is active low as soon as reset goes low and stays low as
long as the watchdog is not properly re-activated by SPI.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33897 | Single-Wire CAN Transceiver(單線CAN收發器) |
| MC33972 | Multiple Switch Detection Interface with Suppressed Wake-Up(帶抑制喚醒功能的多開關檢測接口) |
| MC33976 | Dual Gauge Driver with Configurable Response Time(帶可設置響應時間的雙標尺驅動器) |
| MC33984 | Dual Intelligent High-Current Self-Protected Silicon High-Side Switch (4.0 mOhm)(雙智能大電流帶自保護功能的硅高端開關（4mOhm）) |
| MC33989 | System Basis Chip with High Speed CAN Transceiver(帶高速CAN收發器的系統基片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33889BDW | 功能描述:網絡控制器與處理器 IC SBC LIGHT PASS 3.3 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33889BDWR2 | 功能描述:網絡控制器與處理器 IC SBC LIGHT PASS 3.3 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33889BPEG | 制造商:Freescale Semiconductor 功能描述:SYSTEM BASIS CHIP WITH LOW SPEED FAULT TOLERANT CAN INTERFACE 制造商:Freescale Semiconductor 功能描述:SBC-LITE-LS-CAN - Bulk 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN 28SOIC |
| MC33889BPEGR2 | 制造商:Freescale Semiconductor 功能描述:CAN 125Kbps Sleep/Stop 9V/12V/15V T/R 制造商:Freescale Semiconductor 功能描述:SBC-LITE-LS-CAN - Tape and Reel 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN 28SOIC |
| MC33889DDW | 功能描述:網絡控制器與處理器 IC SBC LIGHT REV D RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。