OPERATIONAL MODES CAN SLEEP MODE The 33742 " />
參數資料
型號： MC33742SDW
廠商： Freescale Semiconductor
文件頁數： 33/71頁
文件大?。?/td> 0K
描述： IC SYSTEM BASE W/LIN 28-SOIC
標準包裝： 26
應用： 自動
接口： SPI
電源電壓： 5.5 V ~ 18 V
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 28-SOIC W
包裝： 管件
安裝類型： 表面貼裝
配用： KIT33742DWEVB-ND - KIT FOR 33742 SBC WITH EHSCAN
Analog Integrated Circuit Device Data
Freescale Semiconductor
39
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
CAN SLEEP MODE
The 33742 offers two CAN Sleep modes:
Sleep mode with CAN wake-up enable: detection of incoming CAN message and SBC wake-up.
Sleep mode with CAN wake-up disable: no detection of incoming CAN message.
The CAN Sleep modes are set via the CAN SPI register.
In CAN Sleep mode (with wake-up enable or disable), the CAN interface is internally supplied from the VSUP pin. The voltage
at V2 pin can be either 5.0 V or turned off. When the CAN is in Sleep mode, the current sourced from V2 is extremely low. In
most cases the V2 voltage is off; however, the CAN can be placed into Sleep mode even with 5.0 V applied on V2.
In CAN Sleep mode, the CANH and CANL drivers are disabled, and the receiver is also disabled. CANH and CANL are high-
impedance mode to ground.
Standby with
External Ballast
Normal or Sleep
0.0 V
LOW
Floating to GND
NO
Sleep
0.0 V
LOW
Floating to GND
NO.
Wake-up if enabled
Stop
Sleep
0.0 V
LOW
Floating to GND
NO.
Wake-up if enabled
Notes
45.
46.
The state of the RXD pin is dependant upon: 1) the V2 voltage, 2) the external circuitry connected to RXD, (i.e. the MCU RXD pin), and
3) any external pull-up between RXD and the 5.0 V supply.
Table 10. CAN Interface/33742 Modes and Pin Status—Operation without Ballast on V2 (47)
Mode
CAN Mode
(Controlled by SPI)
V2 Voltage
TXD Pin
RXD Pin(48)
CANH/CANL
(Disconnected from
Other Node)
CAN
Communication
Unpowered
–
0.0 V
LOW
Floating to GND
NO
Reset (without Ballast)
–
5.0 V
LOW
Floating to GND
NO
Normal Request without
Ballast.
V2 Connected to VDD
–
5.0 V
LOW
5.0 V
Floating to GND
NO
Standby without External
Ballast,.
V2 connected to VDD
Normal or Sleep
5.0 V
0.0 V
5.0 V
Floating to GND
NO
Normal without External
Ballast.
V2 Connected to VDD
Normal
Slew Rate 0, 1, 2,3
5.0 V
Bus Recessive
CANH = CANL = 2.5 V
YES
Normal without External
Ballast,.
V2 Connected to VDD
Sleep
5.0 V
0.0 V
5.0 V
Floating to GND
NO
Sleep
0.0 V
LOW
Floating to GND
NO.
Wake-up if enabled
Stop
Sleep
5.0 V
LOW
Floating to GND
NO.
Wake-up if enabled
Notes
47.
48.
The state of the RXD pin is dependant upon: 1) the V2 voltage, 2) the external circuitry connected to RXD, (i.e. the MCU RXD pin), and
3) any external pull-up between RXD and the 5.0 V supply.
Table 9. CAN Interface/33742S Modes and Pin Status—Operation with Ballast on V2(45)
相關PDF資料
PDF描述
MC33742SDWR2 IC SYSTEM BASE W/LIN 28-SOIC
MC33689DDWB IC SYSTEM BASE W/LIN 32-SOIC
C8051T602-GM IC 8051 MCU 4K-EEPROM 11-QFN
D38999/20ME99PN CONN RCPT 23POS WALL MNT W/PINS
MC100E446FN IC CONV 4BIT SER/PAR ECL 28-PLCC
相關代理商/技術參數
參數描述
MC33742SDWR2 功能描述:網絡控制器與處理器 IC SBC-E-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33742SPEG 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33742SPEGR2 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33761SNT1025 制造商:ON SEMI 功能描述:New
MC33761SNT1-025 功能描述:低壓差穩壓器 - LDO 2.5V 80mA Output RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*