OPERATIONAL MODES Figure 22. CAN Bus Signal" />
參數資料
型號： MC33742EP
廠商： Freescale Semiconductor
文件頁數： 36/71頁
文件大小： 0K
描述： IC SYSTEM BASE W/CAN 48-QFN
標準包裝： 260
應用： 自動
接口： SPI
電源電壓： 5.5 V ~ 18 V
封裝/外殼： 48-VFQFN 裸露焊盤
供應商設備封裝： 48-QFN-EP（7x7）
包裝： 托盤
安裝類型： 表面貼裝
Analog Integrated Circuit Device Data
Freescale Semiconductor
41
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Figure 22. CAN Bus Signal During Can Sleep State and Wake-up Sequence
Figure 23 illustrates how the wake-up signal is generated. First the CAN signal is detected by a low consumption receiver (WU
receiver). Then the signal passes through a pulse width filter, which discards the undesired pulses. The pulse must have a width
bigger than 0.5
s and smaller than 500 s to be accepted. When a pulse is discarded, the pulse counter is reset and no wake-
up signal is generated. When a pulse is accepted, the pulse counter is incremented and, after three pulses, the internal wake-up
signal is asserted.
Each one of the pulses must be spaced by no more than 500
s. If not, the counter will be reset and no wake-up signal will be
generated. This is accomplished by the wake-up timeout generator. The wake-up cycle is completed (and the wake-up flag reset)
when the CAN interface is brought to CAN Normal mode.
Figure 23. Wake-up Functional Block Diagram
CAN WAKE-UP REPORT
The CAN wake-up reporting depend upon the low power mode the SBC is in.
If the SBC is placed into Sleep mode (VDD and V2 off), the CAN wake-up or any wake-up results in the VDD regulator turning
on, leading to turning on the MCU supply and releasing reset. If the 33742 is in Stop mode (V2 off and VDD active), the CAN
wake-up or any wake-up is signalled by a pulse on the INT output. In addition the CANWU bit is set in the CAN register.
If the SBC is in Normal or Standby mode and the CAN interface is in Sleep mode with wake-up enabled, the CAN wake-up is
reported by the CANWU bit in the CAN register.
In the event the SBC is in Normal mode and CAN Sleep mode with wake-up enabled, it is recommended that the user check
for the CANWU bit prior to placing the 33742 in Sleep or Stop mode in case bus traffic has occurred while the CAN interface was
in Sleep mode.
CANL
CANH
TXD
RXD
Ground
2.5 V
CANL Dominant
CANH Dominant
CANL/CANH Recessive
CAN in TXRX Mode
CAN in Sleep Mode (Wake-up Enable)
Incoming CAN Message
CANL Dominant
CANH Dominant
CANL Dominant
CANH Dominant
CANL Dominant
CANH Dominant
WU Receiver
Internal Wake-up Signal
Min 500 ns
Max 500
s
CAN Bus Sleep State
Pulse # 1
Pulse # 2
Pulse # 3
+
Internal Wake-up
Latch
RST
Timeout
RST
Counter
Pulse OK
Narrow
Pulse
Pulse Width
Filter
Timeout
Generator
Standby
WU Receiver
CANH
CANL
Signal
相關PDF資料
PDF描述
V150B5H150BF CONVERTER MOD DC/DC 5V 150W
MS3126F-14-12S CONN PLUG 12POS W/SOCKET CRIMP
V150B5H150B3 CONVERTER MOD DC/DC 5V 150W
V150B48H150BL3 CONVERTER MOD DC/DC 48V 150W
MS27468E21B35S CONN RCPT 79POS JAM NUT W/SCKT
相關代理商/技術參數
參數描述
MC33742EPR2 功能描述:CAN 接口集成電路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33742PEG 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33742PEGR2 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33742PEP 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33742PEPR2 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*