- 您現在的位置：買賣IC網 > PDF目錄359132 > MC33291L (飛思卡爾半導體(中國)有限公司) Eight Output Switch with Serial Peripheral Interface I/O(帶SPI接口的八輸出開關) PDF資料下載
參數資料
| 型號： | MC33291L |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Eight Output Switch with Serial Peripheral Interface I/O(帶SPI接口的八輸出開關) |
| 中文描述： | 8個串行外圍接口的I / O（帶的SPI接口的八輸出開關輸出開關） |
| 文件頁數： | 20/24頁 |
| 文件大?。?/td> | 633K |
| 代理商： | MC33291L |
33291L
20
Go to: www.freescale.com
If the SFPD pin is at 5.0 V, or V
DD
, an output will not be
disabled when an over current is detected. The specific output
will, within 5.0 to 10 μs of encountering the short circuit, go into
an analog current limited mode. This feature is especially useful
when switching incandescent lamp loads, where high in-rush
currents experienced during startup last for 10 to 20
milliseconds.
Each output of the 33291L has its own over current
shutdown circuitry. Over temperature, and the over voltage
faults are not affected by the SFPD pin’s state.
Both load current sensing and output voltage sensing are
incorporated for Short Fault detection with actual detection
occurring slightly
after
the onset of current limit. The current
limit circuitry incorporates a SENSEFET
approach to
measure the total drain current. This calls for the current
through a small number of cells in the power MOSFET to be
measured and the result multiplied by a constant, giving the
total current. Wherein output shutdown circuitry measures the
drain-to-source voltage, shutting down the output if its threshold
(V
Thres
) is exceeded.
Short fault detection is accomplished by sensing the output
voltage and comparing it to V
Thres
. The lowest V
Thres
requires
a voltage of 2.5 V to be sensed. For an enabled output, with
V
DD
= 5.0
±
0.5 V, an output voltage in excess of 3.5 V
will
be
detected as a
short
, or over current condition, while voltages
less than 2.5 V will
not
be detected as
shorts
.
Over Current Recovery
If the SFPD pin is in a high logic state, the circuit returns to
normal operation automatically after the short circuit is removed
(unless thermal shutdown has occurred).
If the SFPD pin is grounded and over current shutdown
occurs, removing the short circuit will result in the output
remaining OFF until the next write cycle. If the short circuit is
not
removed, the output will turn ON for the delay time (70 to 250
μs) and then turn OFF for every write cycle commanding a turn
ON.
SFPD Pin Voltage Selection
Since the voltage condition of the SFPD pin controls the
activation of the short fault protection (i.e., shutdown) mode
equally for all eight outputs, the load having the longest duration
of in-rush current determines what voltage (state) the SFPD pin
should be. Usually if at least one load is, an incandescent lamp
for example, the in-rush current on that input will be
milliseconds in duration. Therefore, setting SFPD at 5.0 V will
prevent shutdown of the output due to the in-rush current. The
system relies only on the over temperature shutdown to protect
the outputs and the loads. The 33291L was designed to switch
GE194 incandescent lamps, or equivalents, with the SFPD pin
in a grounded state. Considerably larger lamps can be switched
with the SFPD pin held in a high logic state.
Sometimes both a delay period greater than 70 to 250 μs
(current limiting of the output) followed by an immediate over
current shutdown is necessary. This can be accomplished by
programming the SFPD pin to 5.0 V for the extended delay
period, allowing the outputs to remain ON in a current limited
mode, then grounding it to accomplish the immediate shutdown
after a period of time. Additional external circuitry is required to
implement this type of function. An MCU parallel output port can
be devoted to controlling the SFPD voltage during and after the
delay period, is often a much better method. In either case, care
should be taken to execute the SFPD start-up routine every
time start-up or reset occurs.
Under Voltage Shutdown
An under voltage V
DD
condition will result in the global
shutdown of all outputs. The under voltage threshold is between
2.5 V and 3.5 V. When V
DD
goes below the threshold, all
outputs are turned OFF, thereby resetting the Serial Output
Data register to indicate the same.
An under voltage condition at the V
PWR
pin will
not
cause
output shutdown and reset. When V
PWR
is between 5.5 V and
9.0 V, the outputs will operate per the command word.
However, the status as reported by the SO pin may not be
accurate below 9.0 V V
PWR
. Proper operation at V
PWR
voltages
below 5.5 V are not be guaranteed.
Deciphering Fault Type
The 33291L SO pin can be used to determine what kind of
system fault has occurred. With eight outputs having open load,
over current, over temperature, and over voltage faults; a total
of 25 different faults are possible. The SO status word received
by the MCU will be compared with the word sent to the 33291L
during the previous write cycle. For a specific output, if the SO
bit compares with the corresponding SI bit of the previous word;
the output is operating normal with no fault. Only when the SO
bit and previous word SI bit differ is there a fault indicated. If the
two words are
not
the same, the MCU should be programmed
to determine which output or outputs are faulted.
If, for a specific output, the initial SI command bit were logic
high, the output would be programmed to be
off
; if, upon the
next command word being entered, a logic low came back on
SO, for that specific output’s corresponding bit, an
output-off
open-load
fault would be indicated. The resulting SO bit, for that
specific output, would be different from that entered during the
previous word for that SI bit, indicating the fault. The eight
output-off open-load faults are therefore most easily detected.
If for a specific output, the initial SI command bit were a logic
low, calling for the output to be programmed
on
; upon the next
word command being entered, the corresponding bit came
back with a logic high on SO, an output over current fault would
be indicated. An over current fault is always reported by the SO
output and is independent of the logic state existing on the
SFPD pin. When the SFPD pin is in a logic high state, an over
current condition will be reported on the SO pin. However,
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33291 | Eight Output Switch with Serial Peripheral Interface I/O(帶SPI接口的八輸出開關) |
| MC33298 | Eight Output Switch with Serial Peripheral Interface I/O(帶SPI接口的八輸出開關) |
| MC33385 | QUAD LOW SIDE DRIVER(四低端驅動器) |
| MC33388 | Fault Tolerant CAN Interface(容錯CAN接口) |
| MC33389 | System Basis Chip with Low Speed Fault Tolerant CAN(帶低速容錯CAN接口的系統基片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33291LDW | 功能描述:IC SWITCH 8X L-SIDE W/SPI 24SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1,000 系列:- 類型:高端/低端驅動器 輸入類型:SPI 輸出數:8 導通狀態電阻:850 毫歐，1.6 歐姆 電流 - 輸出 / 通道:205mA，410mA 電流 - 峰值輸出:500mA，1A 電源電壓:9 V ~ 16 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:PG-DSO-20-45 包裝:帶卷 (TR) |
| MC33292 | 制造商:SPC Multicomp 功能描述:HEATSINK TO220 10.2/W NOTCHED 制造商:SPC Multicomp 功能描述:HEATSINK TO220 10.2C/W NOTCHED 制造商:PRIVATE LABEL 功能描述:HEATSINK TO220 10.2C/W NOTCHED, Packages Cooled:TO-220, Thermal Resistance:10.2 制造商:SPC Multicomp 功能描述:HEAT SINK, Packages Cooled:TO-220, Thermal Resistance:10.2C/W, External Height - Imperial:1.496", External Height - Metric:38mm, External Width - Imperial:1.358", External Width - Metric:34.5mm, External Length - Imperial:0.492" , RoHS Compliant: Yes |
| MC33293 | 制造商:SPC Multicomp 功能描述:CLIP 001 制造商:SPC Multicomp 功能描述:CLIP; Fixing Type:Clip; For Use With:Heat Sinks (MC33285, MC33286, MC33287, MC33288, MC33289, MC33290, MC33291, MC33292); External Length:37.08mm; External Width:3.99mm; Clip Style:Mounting Clip; Length:37.08mm ;RoHS Compliant: Yes |
| MC33293ATV | 制造商:Motorola Inc 功能描述:3 A 4 CHANNEL, BUF OR INV BASED PRPHL DRVR, PZFM15 |
| MC33294 | 制造商:SPC Multicomp 功能描述:CLIP 002 制造商:SPC Multicomp 功能描述:CLIP; Fixing Type:Clip; For Use With:Heat Sinks (MC33272, MC33274); External Length:37.1mm; External Width:7.54mm; Clip Style:Mounting Clip; Length:37.1mm; Overall Length:37.1mm ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。