- 您現在的位置：買賣IC網 > PDF目錄376152 > MC3110 (Electronic Theatre Controls, Inc.) Pilot⑩ Motion Processor PDF資料下載
參數資料
| 型號： | MC3110 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Pilot⑩ Motion Processor |
| 中文描述： | 試點⑩運動處理器 |
| 文件頁數： | 60/81頁 |
| 文件大?。?/td> | 1078K |
| 代理商： | MC3110 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
MC3110 Technical Specifications
60
7 Application Notes
7.1
Design Tips
The following are recommendations for the design of circuits that utilize a PMD Motion Processor.
Serial Interface
If the serial configuration decode logic is not implemented (see section 7.2) the CP data bus should
be tied high. This places the serial interface in a default configuration of 9600,n,8,1 after power on
or reset.
Controlling PWM output during reset
When the motion processor is in a reset state (when the reset line is held low) or immediately after a
power on, the PWM outputs can be in an unknown state, causing undesirable motor movement. It is
recommended that the enable line of any motor amplifier be held in a disabled state by the host
processor or some logic circuitry until communication to the motion processor is established. This
can be in the form of a delay circuit on the amplifier enable line after power up, or the enable line can
be ANDed with the CP reset line.
Parallel word encoder input
When using parallel word input for motor position, it is useful to also decode this information into
the User I/O space. This allows the current input value to be read using the chip instruction ReadIO
for diagnostic purposes.
Using a non standard system clock frequency
It is often desirable to share a common clock among several components in a design. In the case of
the PMD Motion Processors it is possible to use a clock below the standard value of 20MHz. In this
case all system frequencies will be reduced as a fraction of the input clock verses the standard
20MHz clock. The list below shows the affected system parameters:-
Serial baud rate
PWM carrier frequency
Timing characteristics as shown in section 3.2
Cycle time
For example, if an input clock of 17MHz is used with a serial baud rate of 9600 the following timing
changes will result:-
Serial baud rate decreases to 9600 bps *17/20 = 8160 bps
PWM frequency decreases to 20 KHz *17/20 = 17 KHz
Cycle time increases to 102.4
μ
sec *20/17 = 120.48
μ
sec
相關PDF資料 |
PDF描述 |
|---|---|
| MC34063AN | DC-DC Converter Control Circuits |
| MC3448AL | IEEE-488 QUAD BIDIRECTIONAL TRANSCEIVER |
| MC3510 | ECONOLINE: RSZ/P - 1kVDC |
| MC3750 | MC3750 |
| MC380A2 | MC380A2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC3110L | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC3111F | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC3111L | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC3112F | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC3112L | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。