- 您現在的位置：買賣IC網 > PDF目錄376151 > MC1401A-P (Electronic Theatre Controls, Inc.) Advanced Brushless Motor Control Chipset PDF資料下載
參數資料
| 型號： | MC1401A-P |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Brushless Motor Control Chipset |
| 中文描述： | 先進的無刷電機控制芯片組 |
| 文件頁數： | 20/70頁 |
| 文件大?。?/td> | 474K |
| 代理商： | MC1401A-P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
20
will occur, and all new parameters will be ignored except the
position. See the section of this manual entitled "Command Error"
for more information..
Before switching to the S-curve point to point profile mode, the
axis should be at a complete rest.
When the axis is in the S-curve profile mode, the SET_MAX_ACC
command should be used to load the max. acceleration value. The
alternate acceleration loading command SET_ACC can not be
used.
Trapezoidal Point to Point
The following table summarizes the host specified profile parameters
for the trapezoidal point to point profile mode:
Profile
Parameter
Destination
Position
Maximum
Velocity
Accel.
Representation & Range
Units
signed 32 bits
-1,073,741,824 to 1,073,741,823
unsigned 32 bits (1/216 scaling)
0 to 1,073,741,823
unsigned 32 bits (1/216 scaling)
0 to1,073,741,823
counts
counts/smpl
counts/smpl2
In the trapezoidal point to point profile mode the host specifies a
destination position, a maximumvelocity, and an acceleration. The
trajectory is executed by accelerating at the commanded acceleration to
the maximumvelocity where it coasts until decelerating such that the
destination position is reached with the axis at rest (zero velocity). If it is
not possible to reach the maximumvelocity (because deceleration must
begin) then the velocity profile will have no "coasting" phase. The
acceleration rate is the same as the deceleration rate.
A new maximumvelocity and destination position can be specified
while the axis is in motion. When this occurs the axis will accelerate or
decelerate toward the new destination position while attempting to
satisfy the new maximumvelocity condition.
When in Trapezoidal point to point profile mode, to change the
acceleration, the axis must come to a complete stop. After this has
occurred, a new acceleration value can be loaded. If the
acceleration parameter is changed during motion then a
'command error' will occur, and all updated parameters will be
ignored except the position. See the section of this manual
entitled "Command Errors" for more information.
Before switching to the Trapezoidal point to point profile mode,
the axis should be at a complete rest.
The following figure shows a velocity profile for a typical point to point
trapezoidal move, along with a more complicated move involving on the
fly changes to the maximumvelocity and the destination position.
Simple trapezoidal mode motion
Complex trapezoidal mode motion
change max
velocity
change target
position
Vel.
Vel.
Time
Time
Velocity Contouring
The following table summarizes the host specified profile parameters
for the Velocity contouring profile mode:
Profile
Parameter
Maximum
Velocity
Acceleration
Representation & Range
Units
unsigned 32 bits (1/216 scaling)
0 to 1,073,741,823
signed 32 bits*(1/216 scaling)
-1,073,741,824 to 1,073,741,823
counts/smpl
counts/smpl2
*negative numbers using 1/216 scaling are handled no
differently than positive numbers. For example if an
acceration value of -1.95 counts/sample time2 is desired, -
1.95 is multipled by 65,536 and the result is sent to the
chipset (-127,795 dec. or fffe0ccd hex).
In this profile mode the host specifies two parameters, the commanded
acceleration, and the maximumvelocity. The trajectory is executed by
continuously accelerating the axis at the commanded rate until the max.
velocity is reached, or until a new acceleration command is given.
The maximum velocity value must always be positive. Motion
direction is controlled using the acceleration value. Positive
acceleration values result in positive motion, and negative
acceleration values result in negative motion.
There are no restrictions on changing the profile parameters on
the fly. Note that the motion is not bounded by position however.
It is the responsibility of the host to generate acceleration and
max. velocity command values which result in safe motion, within
acceptable position limits.
The following figure shows a typical velocity profile using this mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MC1451A | Advanced Brushless Motor Control Chipset |
| MC1451A-E | Advanced Brushless Motor Control Chipset |
| MC1101A-P | Advanced Brushless Motor Control Chipset |
| MC1211N | LSI CMOS |
| MCY1210N | LSI CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC14020 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:14-Bit Binary Counter |
| MC14020B | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:14-Bit Binary Counter |
| MC14020B_05 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:14−Bit Binary Counter |
| MC14020BCL | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:14-Bit Binary Counter |
| MC14020BCP | 功能描述:計數器移位寄存器 3-18V 14-Bit Binary RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。