- 您現在的位置：買賣IC網 > PDF目錄385564 > MC12U064DACA-2QC00 (SAMSUNG SEMICONDUCTOR CO. LTD.) Dual Voltage MultiMediaCard Specification PDF資料下載
參數資料
| 型號： | MC12U064DACA-2QC00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | Dual Voltage MultiMediaCard Specification |
| 中文描述： | 雙電壓多媒體卡規格 |
| 文件頁數： | 47/64頁 |
| 文件大?。?/td> | 1385K |
| 代理商： | MC12U064DACA-2QC00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
MultiMediaCard
TM
GO_IDLE_STATE (CMD0) is the software reset command, which sets the MultiMediaCard into the Idle
State independently of the current state. In the Inactive State the MultiMediaCard is not affected by this
command. After power-on the MultiMediaCard is always in the Idle State. After power-on or command
GO_IDLE_STATE (CMD0) all output bus drivers of the MultiMediaCard is in a high-impedance state and
the card will be initialized with a default relative card address (“0x0001”). The host runs the bus at the
identification clock rate fOD generated by a push-pull driver stage (refer to also Chapter “Power on” for
more details).
4.10 SPI Communication
The SPI mode consists of a secondary communication protocol. This mode is a subset of the
MultiMediaCard protocol, designed to communicate with a SPI channel, commonly found in Motorola’s
(and lately a few other vendors’) microcontrollers. The interface is selected during the first reset
command after power up (CMD0) and cannot be changed once the part is powered on. The SPI
standard defines the physical link only, and not the complete data transfer protocol. The
MultiMediaCard SPI implementation uses a subset of the MultiMediaCard protocol and command set.
It is intended to be used by systems which require a small number of card (typically one) and have
lower data transfer rates (compared to MultiMediaCard protocol based systems). From the application
point of view, the advantage of the SPI mode is the capability of using an off-the-shelf host, hence
reducing the design-in effort to minimum. The disadvantage is the loss of performance of the SPI
system versus MultiMediaCard (lower data transfer rate, fewer cards, hardware CS per card etc.).
While the MultiMediaCard channel is based on command and data bitstreams which are initiated by a
start bit and terminated by a stop bit, the SPI channel is byte oriented. Every command or data block is
built of 8-bit bytes and is byte aligned to the CS signal (i.e. the length is a multiple of 8 clock cycles).
Similar to the MultiMediaCard protocol, the SPI messages consist of command, response and data-
block tokens (refer to Chapter “Commands” and Chapter “Responses” for a detailed description). All
communication between host and cards is controlled by the host (master). The host starts every bus
transaction by asserting the CS signal low. The response behavior in the SPI mode differs from the
MultiMediaCard mode in the following three aspects:
47
相關PDF資料 |
PDF描述 |
|---|---|
| MC12U128DACA-2QC00 | Dual Voltage MultiMediaCard Specification |
| MC14024B | 7 Stage Ripple Counter(7位二進制計數器) |
| MC14029B | Binary/Decade Up/Down Counter(二/十進制 增/減計數器) |
| MC1403B | Low Voltage Reference(低電壓參考源) |
| MC1403 | Low Voltage Reference(低電壓參考源) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC12U064HACA | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC12U064HACA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC12U064HACB-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC12U064HACC-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC12U064HAFA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
發布緊急采購，3分鐘左右您將得到回復。