- 您現在的位置：買賣IC網 > PDF目錄9305 > MC10EP195FAG (ON Semiconductor)IC DELAY LINE 1024TAP 32-LQFP PDF資料下載
參數資料
| 型號： | MC10EP195FAG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DELAY LINE 1024TAP 32-LQFP |
| 標準包裝： | 250 |
| 系列： | 10EP |
| 標片/步級數： | 1024 |
| 功能： | 可編程 |
| 延遲到第一抽頭： | 2.2ns |
| 接頭增量： | 10ps |
| 可用的總延遲： | 2.2ns ~ 12.2ns |
| 獨立延遲數： | 1 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-LQFP |
| 供應商設備封裝： | 32-LQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | MC10EP195FAGOS |
MC10EP195, MC100EP195
http://onsemi.com
14
An expansion of the latch section of the block diagram is
pictured in Figure 7. Use of this diagram will simplify the
explanation of how the cascade circuitry works. When D10
of chip #1 in Figure 6 is LOW this device’s
CASCADE output will also be low while the CASCADE
output will be high. In this condition the SET MIN pin of
chip #2 will be asserted HIGH and thus all of the latches of
chip #2 will be reset and the device will be set at its minimum
delay.
Chip #1, on the other hand, will have both SET MIN and
SET MAX deasserted so that its delay will be controlled
entirely by the address bus A0—A9. If the delay needed is
greater than can be achieved with 1023 gate delays
(1111111111 on the A0—A9 address bus) D10 will be
asserted to signal the need to cascade the delay to the next
EP195 device. When D10 is asserted, the SET MIN pin of
chip #2 will be deasserted and SET MAX pin asserted
resulting in the device delay to be the maximum delay.
Table 13 shows the delay time of two EP195 chips in
cascade.
To expand this cascading scheme to more devices, one
simply needs to connect the D10 pin from the next chip to
the address bus and CASCADE outputs to the next chip in
the same manner as pictured in Figure 6. The only addition
to the logic is the increase of one line to the address bus for
cascade control of the second programmable delay chip.
SET
MIN
SET
MAX
TO SELECT MULTIPLEXERS
BIT 0
D0 Q0
LEN
Set Reset
BIT 1
D1 Q1
LEN
Set Reset
BIT 2
D2 Q2
LEN
Set Reset
BIT 3
D3 Q3
LEN
Set Reset
BIT 4
D4 Q4
LEN
Set Reset
BIT 5
D5 Q5
LEN
Set Reset
BIT 6
D6 Q6
LEN
Set Reset
BIT 7
D7 Q7
LEN
Set Reset
BIT 8
D8 Q8
LEN
Set Reset
BIT 9
D9 Q9
LEN
Set Reset
Figure 7. Expansion of the Latch Section of the EP195 Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD8400ARZ100-REEL | IC POT DGTL 8BIT SGL 100K 8SOIC |
| MS27484E20F35PB | CONN PLUG 79POS STRAIGHT W/PINS |
| AD8400AR100-REEL | IC POT DIG SGLE 100K 8BIT 8SOIC |
| MS27468T19B11SA | CONN RCPT 11POS JAM NUT W/SCKT |
| AD5161BRM100 | IC POT DGTL 100K 256POS 10-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC10EP195FAR2 | 功能描述:延遲線/計時元素 3.3V ECL RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| MC10EP195FAR2G | 功能描述:延遲線/計時元素 3.3V ECL Programmable Delay RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| MC10EP195MNG | 功能描述:延遲線/計時元素 BBG ECL PRG DLAY CHP RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| MC10EP195MNR4G | 功能描述:延遲線/計時元素 BBG ECL PRG DLAY CHP RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| MC10EP29DT | 功能描述:觸發器 3.3V/5V ECL Dual RoHS:否 制造商:Texas Instruments 電路數量:2 邏輯系列:SN74 邏輯類型:D-Type Flip-Flop 極性:Inverting, Non-Inverting 輸入類型:CMOS 輸出類型: 傳播延遲時間:4.4 ns 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:X2SON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。