- 您現在的位置：買賣IC網 > PDF目錄8102 > MC10EP016FAG (ON Semiconductor)IC COUNTER 8BIT SYNC ECL 32LQFP PDF資料下載
參數資料
| 型號： | MC10EP016FAG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 2/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COUNTER 8BIT SYNC ECL 32LQFP |
| 標準包裝： | 250 |
| 系列： | 10EP |
| 邏輯類型： | 二進制計數器 |
| 方向： | 上 |
| 元件數： | 1 |
| 每個元件的位元數： | 8 |
| 復位： | 異步 |
| 計時： | 同步 |
| 計數速率： | 1.4GHz |
| 觸發器類型： | 正，負 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-LQFP |
| 供應商設備封裝： | 32-LQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | MC10EP016FAGOS |
MC10EP016, MC100EP016
http://onsemi.com
10
APPLICATIONS INFORMATION
Cascading Multiple EP016 Devices
For applications which call for larger than 8-bit counters
multiple EP016s can be tied together to achieve very wide
bit width counters. The active low terminal count (TC)
output and count enable input (CE) greatly facilitate the
cascading of EP016 devices. Two EP016s can be cascaded
without the need for external gating, however for counters
wider than 16 bits external OR gates are necessary for
cascade implementations.
Figure 4 below pictorially illustrates the cascading of 4
EP016s to build a 32-bit high frequency counter. Note the
EP01 gates used to OR the terminal count outputs of the
lower order EP016s to control the counting operation of the
higher order bits. When the terminal count of the preceding
device (or devices) goes low (the counter reaches an all 1s
state) the more significant EP016 is set in its count mode and
will count one binary digit upon the next positive clock
transition. In addition, the preceding devices will also count
one bit thus sending their terminal count outputs back to a
high state disabling the count operation of the more
significant counters and placing them back into hold modes.
Therefore, for an EP016 in the chain to count, all of the lower
order terminal count outputs must be in the low state. The bit
width of the counter can be increased or decreased by simply
adding or subtracting EP016 devices from Figure 4 and
maintaining the logic pattern illustrated in the same figure.
The maximum frequency of operation for a cascaded
counter chain is set by the propagation delay of the TC output,
the necessary setup time of the CE input, and the propagation
delay through the OR gate controlling it (for 16- bit counters
the limitation is only the TC propagation delay and the CE
setup time). Figure 4 shows EP01 gates used to control the
count enable inputs, however, if the frequency of operation is
slow enough, a LVECL OR gate can be used. Using the worst
case guarantees for these parameters.
Figure 4. 32-Bit Cascaded EP016 Counter
CLK
P0 to P7
TC
CLK
P0 to P7
TC
CLK
EP01
P0 to P7
MSB
EP016
Q0 to Q7
EP016
Q0 to Q7
EP016
PE
CE
LSB
EP016
PE
CE
LOAD
LO
CLK
EP01
TC
CLK
PE
CE
CLK
TC
CLK
PE
CE
CLK
Note that this assumes the trace delay between the TC
outputs and the CE inputs are negligible. If this is not the
case estimates of these delays need to be added to the
calculations.
Programmable Divider
The EP016 has been designed with a control pin which
makes it ideal for use as an 8- bit programmable divider. The
TCLD pin (load on terminal count) when asserted reloads the
data present at the parallel input pin (Pn's) upon reaching
terminal count (an all 1s state on the outputs). Because this
feedback is built internal to the chip, the programmable
division operation will run at very nearly the same frequency
as the maximum counting frequency of the device. Figure 5
below illustrates the input conditions necessary for utilizing
the EP016 as a programmable divider set up to divide by 113.
相關PDF資料 |
PDF描述 |
|---|---|
| MC100EP32DTG | IC DIVIDER DIV X2 ECL CLK 8TSSOP |
| MC100EL33DG | IC DIVIDER DIV X4 ECL DIFF 8SOIC |
| MC100LVEL32DG | IC DIVIDER DIV X2 ECL 3.3V 8SOIC |
| MC10EL33DG | IC DIVIDER DIV X4 ECL DIFF 8SOIC |
| MC10EL32DG | IC DIVIDER DIV X2 ECL DIFF 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC10EP016FAR2 | 功能描述:計數器移位寄存器 3.3V/5V ECL 8-Bit RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
| MC10EP016FAR2G | 功能描述:計數器移位寄存器 3.3V/5V ECL 8-Bit Synchronous Binary RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
| MC10EP01D | 功能描述:邏輯門 3.3V/5V ECL 4-Input RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel |
| MC10EP01DG | 功能描述:邏輯門 3.3V/5V ECL 4-Input OR/NOR RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel |
| MC10EP01DR2 | 功能描述:邏輯門 3.3V/5V ECL 4-Input RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。