參數資料
型號： MB95F108AKSPFM
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP64
封裝： PLASTIC, LQFP-64
文件頁數： 5/63頁
文件大?。?/td> 749K
代理商： MB95F108AKSPFM
MB95100AH Series
13
■ HANDLING DEVICES
Preventing Latchup
Care must be taken to ensure that maximum voltage ratings are not exceeded when they are used.
Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if higher than the rating voltage is applied between VCC
pin and VSS pin.
When latchup occurs, power supply current increases rapidly and might thermally damage elements.
Also, take care to prevent the analog power supply voltage (AVCC, AVR) and analog input voltage from exceeding
the digital power supply voltage (VCC) when the analog system power supply is turned on or off.
Stable Supply Voltage
Supply voltage should be stabilized.
A sudden change in power-supply voltage may cause a malfunction even within the guaranteed operating range
of the Vcc power-supply voltage.
For stabilization, in principle, keep the variation in Vcc ripple (p-p value) in a commercial frequency range
(50 Hz to 60 Hz) not to exceed 10% of the standard Vcc value and suppress the voltage variation so that the
transient variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply
is switched.
Precautions for Use of External Clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from subclock mode or stop mode.
■ PIN CONNECTION
Treatment of Unused Input Pin
Leaving unused input pins unconnected can cause abnormal operation or latchup, leaving to permanent damage.
Unused input pins should always be pulled up or down through resistance of at least 2 k
. Any unused input/
output pins may be set to output mode and left open, or set to input mode and treated the same as unused input
pins. If there is unused output pin, make it to open.
Treatment of Power Supply Pins on A/D Converter
Connect to be AVCC
= VCC and AVSS = AVR = VSS even if the A/D converter is not in use.
Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS near
this device.
相關PDF資料
PDF描述
MB95F108AKSPFV 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP64
MB95F108AKWPFV 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP64
MB95R203P-G-SH-JNE2 MICROCONTROLLER, PDIP24
MB95R203PF-G-JNE2 MICROCONTROLLER, PDSO20
MB96F313YSAPMC-GSE2 RISC MICROCONTROLLER, PQFP48
相關代理商/技術參數
參數描述
MB95F108AMS 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F108AMSPFM 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F108AMSPFV 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F108AMW 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F108AMWPFM 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*