- 您現在的位置：買賣IC網 > PDF目錄69023 > MB91V280CR 32-BIT, 32 MHz, RISC MICROCONTROLLER, CPGA401 PDF資料下載
參數資料
| 型號： | MB91V280CR |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, 32 MHz, RISC MICROCONTROLLER, CPGA401 |
| 封裝： | CERAMIC, PGA-401 |
| 文件頁數： | 19/85頁 |
| 文件大小： | 1090K |
| 代理商： | MB91V280CR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MB91270/280 Series
26
Always connect a resonator of 100 kHz or less on dual clock models.
Treatment of N.C. or OPEN pins
Pins marked as N.C. and OPEN must be left open - circuit.
About Mode pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS. To prevent the device erroneously switching to test mode
due to noise, design the printed circuit board such that the distance between the mode pins and VCC or VSS is
as short as possible and the connection impedance is low.
Operation at start-up
The INITX pin must be held at the “L”level when turning on the power.
Source oscillation input at power on
When turning the power on, maintain clock input until the device is released from the oscillation stabilization
wait state.
Caution on Operations during PLL Clock Mode
Even if the oscillator comes off or the clock input stops with the PLL clock selected for this microcontroller, the
microcontroller may continue to operate at the free-running frequency of the PLL’s internal self-oscillating os-
cillator circuit.
Performance of this operation, however, cannot be guaranteed.
External bus setting
This device is guaranteed for use with a 16 MHz external bus.
If the base clock is set to 32 MHz with DIVR1 (external bus base clock division setting register) set to its initial
value, the external bus also operates at 32 MHz. When changing the base clock, first set the external bus so
that it will not exceed 16 MHz.
Pull-up control
The AC characteristics cannot be guaranteed if pull-up resistors are used for pins used as external bus pins.
相關PDF資料 |
PDF描述 |
|---|---|
| MB91V301A | 32-BIT, 68 MHz, RISC MICROCONTROLLER, CPGA179 |
| MB91302APFF-G-XXX-BNDE1 | 32-BIT, MROM, 68 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91302APFF-G-020-BNDE1 | 32-BIT, MROM, 68 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91302APFF-G-001-BNDE1 | 32-BIT, MROM, 68 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB92411-33CR | 4 CHANNEL(S), 33 MHz, DMA CONTROLLER, CPGA179 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91V301A | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:32-Bit Proprietary Microcontroller |
| MB91V301A-RDK01 | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:32-Bit Proprietary Microcontroller |
| MB91V307RCR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit Microcontroller |
| MB91V350A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit Proprietary Microcontroller |
| MB91V650 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。