- 您現在的位置：買賣IC網 > PDF目錄69022 > MB91F465KAPMT-GSE2 (FUJITSU LTD) 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB91F465KAPMT-GSE2 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-120 |
| 文件頁數： | 11/92頁 |
| 文件大小： | 2797K |
| 代理商： | MB91F465KAPMT-GSE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
MB91460K Series
DS07-16606-2E
19
6.
Mode pins (MD_x)
These pins should be connected directly to the power supply or ground pins. To prevent the device from entering
test mode accidentally due to noise, minimize the lengths of the patterns between each mode pin and power
supply pin or ground pin on the printed circuit board as possible and connect them with low impedance.
7.
Notes on operating in PLL clock mode
If the oscillator is disconnected or the clock input stops when the PLL clock is selected, the microcontroller may
continue to operate at the free-running frequency of the self-oscillating circuit of the PLL. However, this self-
running operation cannot be guaranteed.
8.
Pull-up control
The AC standard is not guaranteed in case a pull-up resistor is connected to the pin serving as an external bus pin.
9.
Notes on PS register
As the PS register is processed in advance by some instructions, when the debugger is being used, the exception
handling may result in execution breaking in an interrupt handling routine or the displayed values of the flags in
the PS register being updated.
As the microcontroller is designed to carry out reprocessing correctly upon returning from such an EIT event,
the operation before and after the EIT always proceeds according to specification.
The following behavior may occur if any of the following occurs in the instruction
immediately after a DIV0U/DIV0S instruction:
(a) a user interrupt or NMI is accepted;
(b) single-step execution is performed;
(c) execution breaks due to a data event or from the emulator menu.
1. D0 and D1 flags are updated in advance.
2. An EIT handling routine (user interrupt/NMI or emulator) is executed.
3. Upon returning from the EIT, the DIV0U/DIV0S instruction is executed
and the D0 and D1 flags are updated to the same values as those in 1.
The following behavior occurs when an ORCCR, STILM, MOV Ri,PS instruction is executed
to enable a user interrupt or NMI source while that interrupt is in the active state.
1. The PS register is updated in advance.
2. An EIT handling routine (user interrupt/NMI or emulator) is executed.
3. Upon returning from the EIT, the above instructions are executed and the PS register
is updated to the same value as in 1.
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F467DBPFVS-GSE2 | 32-BIT, FLASH, 96 MHz, RISC MICROCONTROLLER, PQFP208 |
| MB91F467DBPVS-GSE2 | 32-BIT, FLASH, 96 MHz, RISC MICROCONTROLLER, PQFP208 |
| MB91F467DAPFVS-GSE2 | 32-BIT, FLASH, 96 MHz, RISC MICROCONTROLLER, PQFP208 |
| MB91F467DBPFVS-GSE2 | 32-BIT, FLASH, 96 MHz, RISC MICROCONTROLLER, PQFP208 |
| MB91F467MAPMC-GSE2 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP216 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F465KBPMT-GSE2 | 制造商:FUJITSU 功能描述: |
| MB91F465PAPMC-GSE2 | 制造商:FUJITSU 功能描述: |
| MB91F465X | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:The Ultimate Automotive Network |
| MB91F465XAPMC-ESE2 | 制造商:FUJITSU 功能描述: |
| MB91F465XAPMC-GE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。