- 您現在的位置：買賣IC網 > PDF目錄377933 > MB91F368GA (Fujitsu Limited) 32-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | MB91F368GA |
| 廠商： | Fujitsu Limited |
| 元件分類： | 微控制器 |
| 英文描述： | 32-BIT MICROCONTROLLER |
| 中文描述： | 32位微控制器 |
| 文件頁數： | 30/62頁 |
| 文件大小： | 713K |
| 代理商： | MB91F368GA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
FME / EMDC / Br+JR - mb91f367g_f368g_ds.fm 30
10-Apr-01
CHAPTER 3
IO-Map
see appendix A.
The addresses shown in this table for CAN registers are based on the settings for CS7 done in the Boot ROM.
CHAPTER 4
Interrupt Vector Table
see appendix B
.
CHAPTER 5
Power-on-sequence
All VDD pins should be connected to the same potential. The analogue supply voltage (AVCC) must not be turned
on before the digital supply voltage.
Immediately after power on always execute INIT at the INITX pin (input a low level to the INITX pin). Hold this low
level at the INITX pin long enough so that after release of the low level at INITX and the passing of the built in
waiting time stable oscillation of the oscillation circuit is achieved. INITX must be pulled low for at least 8 cycles of
the 4 MHz oscillation clock.
CHAPTER 6
Handling of Unused Input Pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the de-
vice. Therefore they must be tied to VDD or VSS through resistors. In this case those resistors should be more
than 2 KOhm.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
The resistor of more than 2 KOhm is used to limit currents through the protection diodes. In case of voltages at the
unused pin of 0.3 V or more below VSS or 0.3 V or more above VDD currents which could cause latch-up will flow
through those diodes. It is possible to use one resistor to connect several pins to VDD or VSS. Care should be
taken not to connect pins from different supply voltage domains to one resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F367GA | 32-BIT MICROCONTROLLER |
| MB95F106AJW | 8-bit Proprietary Microcontrollers(8位微控制器) |
| MB95FV100D-103 | 8-bit Proprietary Microcontrollers(8位微控制器) |
| MB95F106AJS | 8-bit Proprietary Microcontrollers(8位微控制器) |
| MB95F106AMS | 8-bit Proprietary Microcontrollers(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F368GB | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91F368GBPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB91F368GBPMT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91F369GA | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91F369GAPQS1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。