- 您現在的位置：買賣IC網 > PDF目錄377928 > MB90V595G (Fujitsu Limited) 16-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90V595G |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16-bit Proprietary Microcontroller |
| 中文描述： | 16位微控制器專有 |
| 文件頁數： | 13/47頁 |
| 文件大小： | 657K |
| 代理商： | MB90V595G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
MB90595/595G Series
13
(5) Pull-up/down resistors
The MB90595 Series does not support internal pull-up/down resistors. Use external components where needed.
(6) Crystal Oscillator Circuit
Noises around X0 or X1 pins may cause abnormal operations. Make sure to provide bypass capacitors via
shortest distance from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and make sure
that lines of oscillation circuit not cross the lines of other circuits.
A printed circuit board artwork surrounding the X0 and X1 pins with ground area for stabilizing the operation is
highly recommended.
(7) Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Make sure to turn on the A/D converter power supply (AV
CC
, AVRH, AVRL) and analog inputs (AN0 to AN7)
after turning-on the digital power supply (V
CC
).
Turn-off the digital power after turning off the A/D converter supply and analog inputs. In this case, make sure
that the voltage does not exceed AVRH or AV
CC
(turning on/off the analog and digital power supplies simulta-
neously is acceptable).
(8) Connection of Unused Pins of A/D Converter
Connect unused pins of A/D converter to AV
CC
= V
CC
, AV
SS
= AVRH = DV
CC
= V
SS
.
(9) N.C. Pin
The N.C. (internally connected) pin must be opened for use.
(10) Notes on Energization
To prevent the internal regulator circuit from malfunctioning, set the voltage rise time during energization at 50
μ
s or more (0.2 V to 2.7 V).
(11) Indeterminate outputs from ports 0 and 1
During oscillation setting time of step-down circuit (during a power-on reset) after the power is turned on, the
outputs from ports 0 and 1 become following state.
If RST pin is “H”, the outputs become indeterminate.
If RST pin is “L”, the outputs become high-impedance.
Pay attention to the port output timing shown as follow.
Oscillation setting time
2
Power-on reset
1
Vcc (Power-supply pin)
PONR (power-on reset) signal
RST (external asynchronous reset) signal
RST (internal reset) signal
Oscillation clock signal
KA (internal operation clock A) signal
KB (internal operation clock B) signal
PORT (port output) signal
Period of indeterminated
*1:Power-on reset time: Period of “clock frequency
×
2
17
” (Clock frequency of 16 MHz: 8.19 ms)
*2:Oscillation setting time: Period of “clock frequency
×
2
18
” (Clock frequency of 16 MHz: 16.38ms)
RST pin is “H”
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F598G | 16-bit Proprietary Microcontroller |
| MB90598 | Quadruple 2-Input Positive-OR Gate 14-CDIP -55 to 125 |
| MB90F654A | 16-bit Proprietary Microcontroller |
| MB90P653A | 16-bit Proprietary Microcontroller |
| MB90P653APF | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
| MB9100100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB9100-100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB91101 | 制造商:Panasonic Industrial Company 功能描述:IC |
| MB91101A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。