- 您現在的位置：買賣IC網 > PDF目錄98010 > MB90F912BSPMC (FUJITSU LTD) 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | MB90F912BSPMC |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 6/64頁 |
| 文件大?。?/td> | 1749K |
| 代理商： | MB90F912BSPMC |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
MB90910 Series
14
DS07–13755–2E
■ HANDLING DEVICES
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions :
A voltage higher than VCC pin or lower than VSS pin is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC pin and VSS pin.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
Use meticulous care not to exceed the rating.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVR) exceed the
digital power-supply voltage.
2.
Treatment of unused pins
Leaving unused input pins open may result in permanent damage of the device due to misbehavior or latch-
up. Therefore, they must be pulled up or pulled down through resistors. In this case, those resistors should
be more than 2 k
Ω.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the
above described connection.
3.
Using external clock
The high-speed oscillator pins (X0, X1) can not be used for external clock inputs.
4.
Notes on during operation of PLL clock mode
On this microcontroller, if in case the crystal oscillator breaks off or an external reference clock input stops
while the PLL clock mode is selected, a self-oscillator circuit contained in the PLL may continue its operation
at its self-running frequency. However, Fujitsu will not guarantee results of operations if such failure occurs.
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F243PFV-ES-BND | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP80 |
| MB90F372PMT-G | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP144 |
| MB90F498GPFM | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
| MB90497GPFM | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 |
| MB90F498GPMC | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F947APFR-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F962SPMCR-GE1 | 制造商:FUJITSU 功能描述:IC MCU 16BIT 16LX 48LQFP |
| MB90F962SPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90V340A-102CR | 制造商:FUJITSU 功能描述: |
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
發布緊急采購，3分鐘左右您將得到回復。