- 您現在的位置：買賣IC網 > PDF目錄377918 > MB90F462PFM (FUJITSU LTD) Octal Transparent D-type Latches With 3-State Outputs 20-CFP -55 to 125 PDF資料下載
參數資料
| 型號： | MB90F462PFM |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Octal Transparent D-type Latches With 3-State Outputs 20-CFP -55 to 125 |
| 中文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | PLASTIC, LQFP-64 |
| 文件頁數： | 71/85頁 |
| 文件大小： | 827K |
| 代理商： | MB90F462PFM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MB90460 Series
71
(3) Power-on Reset
(V
CC
=
5.0 V
±
10
%
, V
SS
=
AV
SS
=
0.0 V, T
A
=
40
°
C to
+
85
°
C)
Value
Note : V
CC
must be kept lower than 0.2 V before power-on.
The above values are used for causing a power-on reset.
Some registers in the device are initialized only upon a power-on reset. To initialize these registers, turn the
power supply using the above values.
Parameter
Symbol
Pin name
Condition
Unit
Remarks
Min
Max
Power supply rising time
t
R
V
CC
0.05
30
ms
Power supply cut-off time
t
OFF
V
CC
4
ms
Due to repeated
operations
V
CC
V
CC
3.0 V
V
SS
t
R
t
OFF
2.7 V
0.2 V
0.2 V
0.2 V
RAM data Hold
Sudden changes in the power supply voltage may cause a power-on reset.
To change the power supply voltage while the device is in operation, it is recommended to
raise the voltage smoothly to suppress fluctuations as shown below.
In this case, change the supply voltage with the PLL clock not used. If the voltage drop is 1 V
or fewer per second, however, you can use the PLL clock.
It is recommended to keep the
rising speed of the supply voltage
at 50 mV/ms or slower.
相關PDF資料 |
PDF描述 |
|---|---|
| MB90470 | 16-Bit Proprietary Microcontroller |
| MB90470B | 16-Bit Proprietary Microcontroller |
| MB90473 | 16-Bit Proprietary Microcontroller |
| MB90473PF | 16-Bit Proprietary Microcontroller |
| MB90473PFV | 16-Bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F474HPF-GE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU I2C SMD QFP100 |
| MB90F474HPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F474HPMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F474LPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F474LPMCR-GE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。