- 您現在的位置：買賣IC網 > PDF目錄377917 > MB90F457SPMT (FUJITSU LTD) Octal Registered Transceiver With 3-State Outputs 24-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MB90F457SPMT |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Octal Registered Transceiver With 3-State Outputs 24-CDIP -55 to 125 |
| 中文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 13/78頁 |
| 文件大?。?/td> | 680K |
| 代理商： | MB90F457SPMT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
MB90455 Series
13
Caution on Operations during PLL Clock Mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
Sequence of turning on power of A/D converter and applying analog input
Be sure to turn on digital power (Vcc) before applying signals to the A/D converter and applying analog input
signals (AN0 to AN7 pins).
Be sure to turn off the power of A/D converter and analog input before turning off the digital power source.
Be sure not to apply AVR exceeding AVcc when turning on and off. (No problems occur if analog and digital
power is turned on and off simultaneously.)
Handling pins when A/D converter is not used
If the A/D converter is not used, connect the pins under the following conditions: “AVcc=AVR=Vcc,” and
“Avss=Vss”
Note on turning on power
For preventing malfunctions on built-in step-down circuit, maintain a minimum of 50
μ
s of voltage rising time
(between 0.2 V and 2.7 V) when turning on the power.
Stabilization of supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the specified Vcc
supply voltage operating range. Therefore, the Vcc supply voltage should be stabilized.
For reference, the supply voltage should be controlled so that Vcc ripple variations (peak-to-peak values) at
commercial frequencies (50 Hz to 60 Hz) fall below 10
%
of the standard V
CC
supply voltage and the coefficient
of fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
相關PDF資料 |
PDF描述 |
|---|---|
| MB90455 | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-CDIP -55 to 125 |
| MB90456 | 16-bit Proprietary Microcontroller |
| MB90460 | 16-bit Proprietary Microcontroller |
| MB90462 | 16-bit Proprietary Microcontroller |
| MB90462P-SH | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F462APFM-GE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU SMD LQFP64 |
| MB90F462AP-G-SHE1 | 制造商:FUJITSU 功能描述:16-bit Proprietary Microcontroller |
| MB90F462APMC-G-SPE1 | 制造商:FUJITSU 功能描述:16-Bit MCU 制造商:FUJITSU 功能描述:16-bit Microcontroller |
| MB90F462APMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F462APMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。