- 您現在的位置：買賣IC網 > PDF目錄69020 > MB90F352SPFV (FUJITSU LTD) 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB90F352SPFV |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | PLASTIC, LQFP-64 |
| 文件頁數： | 11/64頁 |
| 文件大?。?/td> | 800K |
| 代理商： | MB90F352SPFV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
MB90350 Series
19
11. Notes on Energization
To prevent the internal regulator circuit from malfunctioning, set the voltage rise time during energization at 50
or more
s (0.2 V to 2.7 V)
12. Stabilization of power supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the specified VCC supply
voltage operating range. Therefore, the VCC supply voltage should be stabilized.
For reference, the supply voltage should be controlled so that VCC ripple variations (peak-to-peak value) at
commercial frequencies (50 Hz to 60 Hz) fall below 10
% of the standard VCC supply voltage and the coefficient
of fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
13. Initialization
In the device, there are internal registers which are initialized only by a power-on reset. To initialize these registers,
turn on the power again.
14. Port 0 to port 3 output during Power-on (External-bus mode)
As shown below, when power is turned on in External-Bus mode, there is a possibility that output signal of
Port 0 to Port 3 might be unstable.
15. Notes on using CAN Function
To use CAN function, please set ’1’ to DIRECT bit of CAN Direct Mode Register (CDMR).
If DIRECT bit is set to ’0’ (initial value), wait states will be performed when accessing CAN registers.
Please refer to Hardware Manual of MB90350 series for detail of CAN Direct Mode Register.
16. Flash security Function
The security byte is located in the area of the flash memory.
If protection code 01H is written in the security bit, the flash memory is in the protected state by security.
Therefore please do not write 01H in this address if you do not use the security function.
Please refer to following table for the address of the security bit.
Flash memory size
Address for security bit
MB90F352
Embedded 1 Mbit Flash Memory
FE0001H
Port0 to Port3
Port0 to Port3 outputs
might be unstable
Port0 to Port3 outputs = Hi-Z
VCC
1/2 VCC
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F352PFV | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64 |
| MB90352CSPFV | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64 |
| MB90387PMT | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48 |
| MB90F387SPMT | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 |
| MB90523BPFV | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F352SPMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F352SPMC-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F352TESPMCRGE1 | 制造商:FUJI 功能描述:New |
| MB90F352TESPMCR-GE1 | 制造商:FUJITSU 功能描述:MCU 16BIT 16LX 128K FLASH 64LQFP 制造商:FUJITSU 功能描述:MCU, 16BIT, 16LX, 128K FLASH, 64LQFP 制造商:FUJITSU 功能描述:IC, 16BIT MCU, F2MC-16LX, 24MHZ, LQFP-64; Controller Family/Series:F2MC-16LX; Core Size:16bit; No. of I/O's:51; Supply Voltage Min:3V; Supply Voltage Max:5.5V; Digital IC Case Style:LQFP; No. of Pins:64; Program Memory Size:128KB ;RoHS Compliant: Yes |
| MB90F362ESPMCR-GE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。