- 您現在的位置：買賣IC網 > PDF目錄377924 > MB90F351TEPMC1 (FUJITSU LTD) 16-bit Proprietary Microcontrollers PDF資料下載
參數資料
| 型號： | MB90F351TEPMC1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontrollers |
| 中文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 25/85頁 |
| 文件大?。?/td> | 880K |
| 代理商： | MB90F351TEPMC1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MB90350E Series
25
6.
Treatment of Power Supply Pins (V
CC
/V
SS
)
If there are multiple V
CC
and V
SS
pins, from the point of view of device design, pins to be of the same potential
are connected inside of the device to prevent malfunction such as latch-up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the V
CC
and V
SS
pins to the power supply
and ground externally.
Connect V
CC
and V
SS
pins to the device from the current supply source at a possibly low impedance.
As a measure against power supply noise, it is recommended to connect a capacitor of about 0.1
μ
F as a
bypass capacitor between V
CC
and V
SS
pins in the vicinity of V
CC
and V
SS
pins of the device.
7.
Pull-up/down resistors
The MB90350E series does not support internal pull-up/down resistors (Port 0 to Port 3: built-in pull-up resistors).
Use external components where needed.
Crystal oscillator circuit
8.
Noise around the X0/X1, or X0A/X1A pins may cause this device to operate abnormally. In the interest of stable
operation it is strongly recommended that printed circuit artwork places ground bypass capacitors as close as
possible to the X0/X1, X0A/X1A and crystal oscillator (or ceramic oscillator) and that oscillator lines do not cross
the lines of other circuits.
Please ask each crystal maker to evaluate the oscillational characteristics of the crystal and this device.
Turning-on sequence of power supply to A/D converter and analog inputs
9.
Make sure to turn on the A/D converter power supply (AV
CC
, AVRH) and analog inputs (AN0 to AN14) after
turning-on the digital power supply (V
CC
) .Turn-off the digital power after turning off the A/D converter power
supply and analog inputs. In this case, make sure that the voltage does not exceed AVRH or AV
CC
(turning on/
off the analog and digital power supplies simultaneously is acceptable).
10. Connection of unused pins of A/D converter if A/D converter is not used
Connect unused pins of A/D converter to AV
CC
=
V
CC
, AV
SS
=
AVRH
=
V
SS
.
11. Notes on energization
To prevent the internal regulator circuit from malfunctioning, set the voltage rise time during energization at
50
μ
s or more (0.2 V to 2.7 V) .
Vcc
Vss
Vss
Vcc
Vss
Vcc
MB90350E
Series
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F351TESPMC | 16-bit Proprietary Microcontrollers |
| MB90F351TESPMC1 | 16-bit Proprietary Microcontrollers |
| MB90F352EPMC | 16-bit Proprietary Microcontrollers |
| MB90F352EPMC1 | 16-bit Proprietary Microcontrollers |
| MB90F352ESPMC | 16-bit Proprietary Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F352ESPMCR-GSE2 | 制造商:FUJITSU 功能描述: |
| MB90F352PMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F352PMC-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F352SPFM-GSE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU CAN 5V SMD LQFP64 |
| MB90F352SPMC-GSE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。