- 您現在的位置：買賣IC網 > PDF目錄377920 > MB90623A (Fujitsu Limited) 16-Bit Proprietary Microcontroller(16位專用微控制器) PDF資料下載
參數資料
| 型號： | MB90623A |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16-Bit Proprietary Microcontroller(16位專用微控制器) |
| 中文描述： | 16位微控制器專利（16位專用微控制器） |
| 文件頁數： | 12/82頁 |
| 文件大?。?/td> | 797K |
| 代理商： | MB90623A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
MB90620A Series
12
I
HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than V
pins other than medium- and high voltage pins or if higher than the voltage is applied between V
CC
or lower than V
SS
is applied to the input and output
CC
and V
SS
.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
2. Treatment of Unused Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistors.
3. External Reset Input
To reset the internal circuit by the Low-level input to the RST pin, the Low-level input to the RST pin must be
maintained for at least five machine cycles. Pay attention to it if the chip uses external clock input.
4. V
CC
and V
SS
Pins
Apply equal potential to the V
CC
and V
SS
pins.
5. Precautions when Using an External Clock
When an external clock is used, drive X0 pin.
6. Power-on Sequence for A/D Converter Power Supplies and Analog Inputs
Be sure to turn on the digital power supply (V
CC
) before applying voltage to the A/D converter power supplies
(AV
CC
, AVRH, and AVRL) and analog inputs (AN0 to AN15).
In addition, when the power is turned off, turn off the A/D converter power supplies (AV
CC
, AVRH, and AVRL)
and analog inputs (AN0 to AN15) first, then the digital power supply (AV
CC
).
Whether applying or cutting off the power, be certain that AVRH does not exceed AV
CC
.
7. Pin set when turning on power supplies
In the MB90P623, all of the bits (48 K
×
8 bits) are set to “1” when the IC is shipped from Fujitsu and after
erasure. To input data, program, the IC by selectively setting the desired bits to “0”. Bits cannot be set to “1”
electrically.
X0, (X0A)
X1, (X1A)
MB90620A
Using of External Clock
相關PDF資料 |
PDF描述 |
|---|---|
| MB90622PFV | 9-Bit Bus-Interface D-type Latches With 3-State Outputs 28-LCCC -55 to 125 |
| MB90P623A | 16-bit Proprietary Microcontroller |
| MB90P623PFV | 16-bit Proprietary Microcontroller |
| MB90623PFV | 9-Bit Bus-Interface D-type Latches With 3-State Outputs 24-CDIP -55 to 125 |
| MB90632APF | 9-Bit Bus-Interface D-type Latches With 3-State Outputs 24-CDIP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90623PFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90632A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90632APF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90632APFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90634A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。