參數資料
型號： MAX9967ADCCQ+TD
廠商： Maxim Integrated Products
文件頁數： 19/30頁
文件大?。?/td> 0K
描述： IC DCL DUAL 500MBPS ATE 100TQFP
標準包裝： 250
系列： ATE
邏輯類型： 比較器, 驅動器
電源電壓： -1.5 V ~ 6.5 V
位數： 2
工作溫度： 0°C ~ 70°C
安裝類型： *
封裝/外殼： *
供應商設備封裝： *
包裝： *
MAX9967
Dual, Low-Power, 500Mbps ATE
Driver/Comparator with 35mA Load
26
______________________________________________________________________________________
Serial Interface and Device Control
A CMOS-compatible serial interface controls the
MAX9967 modes (Figure 5). Control data flow into an 8-
bit shift register (MSB first) and are latched when CS is
taken high, as shown in Figure 6. Latches contain 6 con-
trol bits for each channel of the dual pin driver. Data
from the shift register are loaded to either or both of the
latches as determined by bits D6 and D7, and indicated
in Figure 5 and Table 5. The control bits, in conjunction
with external inputs DATA_ and RCV_, manage the fea-
tures of each channel, as shown in Tables 1 and 2. RST
sets LLEAK = 1 for both channels, forcing them into low-
leakage mode. All other bits are unaffected. At power-
up, hold RST low until VCC and VEE have stabilized.
Analog control input THR sets the threshold for the
input logic, allowing operation with CMOS logic as low
as 0.9V. Leaving THR unconnected results in a nominal
threshold of 1.25V from an internal reference, providing
compatibility with 2.5 to 3.3V logic.
SCLK
DIN
D7
D6
D5
D4
D3
D2
D1
D0
tCH
tCSS0
tOH
tCL
tCSS1
tCSH1
tCSWH
tDS
CS
Figure 6. Serial-Interface Timing
BIT
NAME
DESCRIPTION
D7
CH1
Channel 1 Write Enable. Set to 1 to update the control byte for channel 1. Set to 0 to make no changes to
channel 1.
D6
CH2
Channel 2 Write Enable. Set to 1 to update the control byte for channel 2. Set to 0 to make no changes to
channel 2.
D5
LLEAK
Low-Leakage Select. Set to 1 to put driver, load, and clamps into low-leakage mode. Comparators remain
active in low-leakage mode. Set to 0 for normal operation.
D4
TMSEL
Driver Termination Select. Set to 1 to force the driver output to the DTV_ voltage when RCV_ = 1 (term). Set to
0 to place the driver into high-impedance mode when RCV_ = 1 (high-Z). See Table 1.
D3
SC1
D2
SC0
Driver Slew-Rate Select. SC1 and SC0 set the driver slew rate. See Table 2.
D1
LDDIS
Load Disable. Set LDDIS to 1 to disable the load. Set to 0 for normal operation. See Table 4.
D0
LDCAL
Load Calibrate. Overrides LDEN to enable load. Set LDCAL to 1 to enable load. Set LDCAL to 0 for normal
operation. See Table 4.
Table 5. Shift-Register Functions
相關PDF資料
PDF描述
MS27497E24F29P CONN RCPT 29POS WALL MNT W/PINS
D38999/26FJ43PN CONN PLUG 43POS STRAIGHT W/PINS
MS3116P20-41P CONN PLUG 41POS STRAIGHT W/PINS
MAX9967BRCCQ+D IC DCL DUAL 500MBPS ATE 100TQFP
MAX1224CTC+ IC ADC 12BIT 1.5MSPS 12-TQFN
相關代理商/技術參數
參數描述
MAX9967ALCCQ 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX9967ALCCQ+D 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
MAX9967ALCCQ+TD 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
MAX9967ALCCQ-D 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
MAX9967ALCCQ-TD 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*