- 您現在的位置：買賣IC網 > PDF目錄2092 > MAX9877EWP+TG45 (Maxim Integrated Products)IC AUDIO SUBSYSTEM 20-WLP PDF資料下載
參數資料
| 型號： | MAX9877EWP+TG45 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/30頁 |
| 文件大小： | 0K |
| 描述： | IC AUDIO SUBSYSTEM 20-WLP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive® |
| 類型： | D 類 |
| 輸出類型： | 1-通道（單聲道），帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 825mW x 1 @ 4 歐姆; 53mW x 2 @ 16 歐姆 |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 特點： | 消除爆音，I²C，輸入多路復用器，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 20-WLP |
| 封裝/外殼： | 20-WFBGA，WLBGA |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
MAX9877
Low RF Susceptibility, Mono Audio
Subsystem with DirectDrive Headphone Amplifier
24
______________________________________________________________________________________
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START CONDITION
START
CONDITION
tHD:STA
tSU:STA
tBUF
tSU:STO
tLOW
tSU:DAT
tHD:DAT
tHIGH
tR
tF
Figure 6. 2-Wire Interface Timing Diagram
SCL
SDA
SSr
P
Figure 7. START, STOP, and REPEATED START Conditions
SMBus is a trademark of Intel Corp.
I2C Interface Specification
The MAX9877 features an I2C/SMBus-compatible, 2-
wire serial interface consisting of a serial-data line
(SDA) and a serial-clock line (SCL). SDA and SCL facil-
itate communication between the MAX9877 and the
master at clock rates up to 400kHz. Figure 6 shows the
2-wire interface timing diagram. The master generates
SCL and initiates data transfer on the bus. The master
device writes data to the MAX9877 by transmitting the
proper slave address followed by the register address
and then the data word. Each transmit sequence is
framed by a START (S) or REPEATED START (Sr) con-
dition and a STOP (P) condition. Each word transmitted
to the MAX9877 is 8 bits long and is followed by an
acknowledge clock pulse. A master reading data from
the MAX9877 transmits the proper slave address fol-
lowed by a series of nine SCL pulses. The MAX9877
transmits data on SDA in sync with the master-generat-
ed SCL pulses. The master acknowledges receipt of
each byte of data. Each read sequence is framed by a
START (S) or REPEATED START (Sr) condition, a not
acknowledge, and a STOP (P) condition. SDA operates
as both an input and an open-drain output. A pullup
resistor, typically greater than 500
Ω, is required on
SDA. SCL operates only as an input. A pullup resistor,
typically greater than 500
Ω, is required on SCL if there
are multiple masters on the bus, or if the single master
has an open-drain SCL output. Series resistors in line
with SDA and SCL are optional. Series resistors protect
the digital inputs of the MAX9877 from high voltage
spikes on the bus lines, and minimize crosstalk and
undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL cycle. The
data on SDA must remain stable during the high period
of the SCL pulse. Changes in SDA while SCL is high
are control signals (see the
START and STOP
Conditions section).
START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A
master initiates communication by issuing a START con-
dition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high
transition on SDA while SCL is high (Figure 7). A START
condition from the master signals the beginning of a
transmission to the MAX9877. The master terminates
transmission, and frees the bus, by issuing a STOP con-
dition. The bus remains active if a REPEATED START
condition is generated instead of a STOP condition.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9879ERV+T | IC AUDIO SUBSYSTEM 30-UCSP |
| MAX987EUK-T | IC COMP MICRPWR R-R I/O SOT23-5 |
| MAX9888EWY+T | IC CODEC AUDIO FLEXSOUND 63WLP |
| MAX9890AEBL+T | IC SUPP CLICK-POP 9-UCSP |
| MAX9892ELT+T | IC ELIMINATOR CLICK/POP 6UDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9879ERV+T | 功能描述:音頻放大器 Audio Subsystem w/DirectDrive RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9879EVKIT+ | 功能描述:音頻放大器 Stereo Class D Audio Subsystem with DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX987ESA | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX987ESA+ | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX987ESA+T | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。