- 您現在的位置：買賣IC網 > PDF目錄10268 > MAX9770ETI+ (Maxim Integrated Products)IC AMP AUDIO 1.2W MONO D 28TQFN PDF資料下載
參數資料
| 型號： | MAX9770ETI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO 1.2W MONO D 28TQFN |
| 標準包裝： | 60 |
| 類型： | D 類 |
| 輸出類型： | 1-通道（單聲道），帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 1.2W x 1 @ 8 歐姆; 80mW x 2 @ 16 歐姆 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 特點： | 消除爆音，輸入多路復用器，靜音，短路和熱保護，關機 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 包裝： | 管件 |
MAX9770
Charge-Pump Capacitor Selection
Use capacitors with an ESR less than 100m
Ω for opti-
mum performance. Low-ESR ceramic capacitors mini-
mize the output resistance of the charge pump. Most
surface-mount ceramic capacitors satisfy the ESR
requirement. For best performance over the extended
temperature range, select capacitors with an X7R
dielectric. Table 5 lists suggested manufacturers.
Flying Capacitor (C1)
The value of the flying capacitor (C1) affects the load
regulation and output resistance of the charge pump. A
C1 value that is too small degrades the device’s ability to
provide sufficient current drive, which leads to a loss of
output voltage. Increasing the value of C1 may improve
load regulation and reduces the charge-pump output
resistance to an extent. Above 1F, the on-resistance of
the switches and the ESR of C1 and C2 dominate.
Output Capacitor (C2)
The output capacitor value and ESR directly affect the
ripple at CPVSS. Increasing the value of C2 reduces
output ripple. Likewise, decreasing the ESR of C2
reduces both ripple and output resistance. Lower
capacitance values can be used in systems with low
maximum output power levels. See the Output Power
vs. Charge-Pump Capacitance and Load Resistance
graph in the
Typical Operating Characteristics.
CPVDD Bypass Capacitor
The CPVDD bypass capacitor (C3) lowers the output
impedance of the power supply and reduces the impact
of the MAX9770’s charge-pump switching transients.
Bypass CPVDD with C3, the same value as C1, and
place it physically close to the CPVDD and PGND (refer
to the MAX9770 EV kit for a suggested layout).
Layout and Grounding
Proper layout and grounding are essential for optimum
performance. Use large traces for the power-supply
inputs and amplifier outputs to minimize losses due to
parasitic trace resistance, as well as route the head
away from the device. Good grounding improves audio
performance, minimizes crosstalk between channels,
and prevents any switching noise from coupling into the
audio signal. Connect CPGND, PGND, and GND
together at a single point on the PC board. Route
CPGND and all traces that carry switching transients
away from GND, PGND, and the traces and compo-
nents in the audio signal path.
Connect all components associated with the charge
pump (C2 and C3) to the CPGND plane. Connect SVSS
and CPVSS together at the device. Place the charge-
pump capacitors (C1, C2, and C3) as close to the
device as possible. Bypass VDD and PVDD with a 1F
capacitor to GND. Place the bypass capacitors as
close to the device as possible.
Use large, low-resistance output traces. As load imped-
ance decreases, the current drawn from the device out-
puts increase. At higher current, the resistance of the
output traces decrease the power delivered to the load.
Large output, supply, and GND traces also improve the
power dissipation of the device.
The MAX9770 thin QFN package features an exposed
thermal pad on its underside. This pad lowers the pack-
age’s thermal resistance by providing a direct heat con-
duction path. Due to the high efficiency of the MAX9770’s
Class D amplifier, additional heatsinking is not required. If
additional heatsinking is required, connect the exposed
paddle to GND. See the MAX9770 EV kit data sheet for
suggested component values and layout guidelines.
1.2W, Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
18
______________________________________________________________________________________
Table 5. Suggested Capacitor Manufacturers
SUPPLIER
PHONE
FAX
WEBSITE
Taiyo Yuden
800-348-2496
847-925-0899
www.t-yuden.com
TDK
807-803-6100
847-390-4405
www.component.tdk.com
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9757ETJ+ | IC AMP AUDIO PWR 2.3W AB 32TQFN |
| MAX9750BETI+ | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| MS27656E13F8PC | CONN RCPT 8POS WALL MNT W/PINS |
| AD7683BCPZRL | IC ADC 16BIT 100KSPS 8LFCSP |
| LTC2366HTS8#TRMPBF | IC ADC 12BIT 3MSPS TSOT23-8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9770ETI+ | 功能描述:音頻放大器 1.2W Low-EMI Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9770ETI+T | 功能描述:音頻放大器 1.2W Low-EMI Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9770EUI | 制造商:Rochester Electronics LLC 功能描述: |
| MAX9770EUI+ | 功能描述:音頻放大器 1.2W Low-EMI Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9770EUI+T | 功能描述:音頻放大器 1.2W Low-EMI Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。