- 您現在的位置：買賣IC網 > PDF目錄11137 > MAX7357EUG+T (Maxim Integrated Products)IC MULTIPLEXER 8X1 24TSSOP PDF資料下載
參數資料
| 型號： | MAX7357EUG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/22頁 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLEXER 8X1 24TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 多路復用器 |
| 電路： | 1 x 8:1 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 帶卷 (TR) |
MAX7356/MAX7357/MAX7358
1-to-8 I2C Bus Switches/Multiplexers with Bus
Lock-Up Detection, Isolation, and Notification
14
______________________________________________________________________________________
B7
B6
B5
B4
B3
B2
B1
B0
COMMAND
X
XXXX
X
0
Interrupt with
RST/INT disabled
X
XXXX
X
1
Interrupt with
RST/INT enabled
X
XXXX0
X
Flush-out disabled
X
XXXX1
X
Flush-out enabled
X
XXX
0
X
RST/INT released after a register read
X
XXX
1
X
RST/INT released after 1.6 seconds
XX
X
0
X
XX
The lock-up register shows the current
condition
XX
X
1
X
XX
The lock-up register data is not cleared
until a read
X
0
X
Disconnect all channels on bus lock-up
X
1
X
Disconnect only the locked up bus
X
0
X
Bus lock-up detection enabled
X
1
X
Bus lock-up detection disabled
X
0
XXXX
X
Enhanced mode
X
1
XXXX
X
Basic mode enabled
0
X
XXXX
X
Preconnect test is disabled
1
X
XXXX
X
Preconnect test is enabled
Table 5. Configuration Register Definition
X = Don’t care.
be selected. More than one channel can be selected
simultaneously. When a channel is selected, the channel
becomes active immediately after a stop condition has
been placed on the I2C bus. This ensures that all
SC_/SD_ lines are in a HIGH state when the channel is
made active, so that no false conditions are generated at
the time of connection.
Configuration Register
(MAX7357/MAX7358)
B0 =
RST/INT serves as an interrupt when a bus lock-
up condition is detected.
B1 = Flush-out sequence is sent automatically on locked-
up channels when a lock-up condition is detected.
B2 = When B0 = 1, release the
RST/INT output after
asserting for 1.6 seconds.
B3 = Data in the lock-up indication register cleared only
after reading the register.
B4 = Connected channels remain connected on detec-
tion of lock-up if the lock-up condition is present only on
a channel that is not connected.
B5 = Disable bus lock-up detection.
B6 = Basic mode.
B7 = Enables the preconnection wiggle test for SC_
and SD_.
Flush-Out Sequence Register
(MAX7357/MAX7358)
A flush-out sequence can be sent to a particular auxil-
iary bus automatically after the identification of the lock-
up condition. The flush-out sequence consists of 18
SC_ clock cycles. An 8-bit sequence for the SD_ to fol-
low during the flush-out cycle can also be defined by
writing to the flush-out sequence register. By default,
the flush-out sequence register is all ones. The
MAX7357 or MAX7358 attempt to send the one-byte
sequence followed by an additional clock cycle (NACK)
two times sequentially, followed by a stop condition.
The effectiveness of sending the flush-out sequence
depends on the behavior of the locked-up device. For
an auxiliary bus with only slave devices, it is more likely
that the SCL line can still be driven by the MAX7357 or
MAX7358. In this case, a slave device may respond to
a particular flush-out sequence. After the release of the
SD_ line by a “stuck” device, the remaining sequence
on the SD_ line can be used to reset itself.
Bus Lock-Up Indication Register
(MAX7357/MAX7358)
The bus master can read the lock-up indication byte to
identify the stuck channels. A bit set to ”1” indicates
that the associated channel is stuck. The indication for
a given channel remains as long as the lock-up condi-
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BWY-IW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| MAX4527CSA+T | IC SWITCH DUAL SPDT 8SOIC |
| VE-J6D-IW-F2 | CONVERTER MOD DC/DC 85V 100W |
| VI-BWX-IY-F3 | CONVERTER MOD DC/DC 5.2V 50W |
| MAX4066CSD+ | IC SWITCH QUAD SPST 14SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7358ETG+ | 功能描述:多路器開關 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX7358ETG+T | 功能描述:多路器開關 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX7358EUG+ | 功能描述:多路器開關 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX7358EUG+T | 功能描述:多路器開關 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX7358EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX7358 EVAL KIT - Boxed Product (Development Kits) |
發布緊急采購，3分鐘左右您將得到回復。