- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6678AEP92+ (Maxim Integrated)IC TEMP MONITOR 2CH PWM 20-QSOP Datasheet資料下載
參數資料
| 型號： | MAX6678AEP92+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 6/19頁 |
| 文件大?。?/td> | 669K |
| 描述： | IC TEMP MONITOR 2CH PWM 20-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 功能： | 溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 精確度： | ±4°C（最小值） |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 20-QSOP |
| 包裝： | 管件 |
SMBus Digital Interface
From a software perspective, the MAX6678 appears as a
set of byte-wide registers. This device uses a standard
SMBus 2-wire/I
2
C-compatible serial interface to access
the internal registers. The MAX6678 has four different
slave addresses available; therefore, a maximum of four
MAX6678 devices can share the same bus.
The MAX6678 employs four standard SMBus protocols:
write byte, read byte, send byte, and receive byte
(Figures 1, 2, and 3). The shorter receive byte protocol
allows quicker transfers, provided that the correct data
register was previously selected by a read byte instruc-
tion. Use caution with the shorter protocols in multimaster
systems, since a second master could overwrite the
command byte without informing the first master.
Temperature data can be read from registers 00h and
01h. The temperature data format for these registers is
8 bits, with the LSB representing 1癈 (Table 1) and the
MSB representing +128癈. The MSB is transmitted first.
All values below 0癈 clip to 00h.
Table 2 details the register address and function, whether
they can be read or written to, and the power-on reset
(POR) state. See Tables 26 for all other register functions
and the Register Descriptions section.
Temperature Reading
The MAX6678 contains two external temperature mea-
surement inputs to measure the die temperature of CPUs
or other ICs having on-chip temperature-sensing diodes,
or discrete diode-connected transistors as shown in the
Typical Operating Circuits. For best accuracy, the dis-
crete diode-connected transistor should be a small-signal
device with its collector and base connected together.
The on-chip ADC converts the sensed temperature and
outputs the temperature data in the format shown in Table
1. Temperature channel 2 can be used to measure either
a remote thermal diode or the internal temperature of the
MAX6678. Bit D1 of register 02h (Table 2) selects local or
remote sensing for temperature channel 2 (1 = local). The
temperature measurement resolution is 1癈 for both local
and remote temperatures. The temperature accuracy is
within ?癈 for remote temperature measurements from
+60癈 to +100癈.
2-Channel Temperature Monitor with Dual Automatic
PWM Fan-Speed Controller and Five GPIOs
6 _______________________________________________________________________________________
Write Byte Format
Read Byte Format
Send Byte Format
Receive Byte Format
Slave address: equiva-
lent to chip-select line of
a 3-wire interface
Command byte: selects which
register you are writing to
Data byte: data goes into the register
set by the command byte (to set
thresholds, configuration masks, and
sampling rate)
Slave address: equivalent
to chip-select line
Command byte: selects
which register you are
reading from
Slave address: repeated
due to change in data-
flow direction
Data byte: reads from
the register set by the
command byte
Command byte: sends com-
mand with no data, usually
used for one-shot command
Data byte: reads data from
the register commanded
by the last read byte or
write byte transmission;
also used for SMBus alert
response return address
S = Start condition
Shaded = Slave transmission
P = Stop condition
/// = Not acknowledged
Figure 1. SMBus Protocols
S
ADDRESS
RD
ACK
DATA
///
P
7 bits
8 bits
WR
S
ACK
COMMAND
ACK
P
8 bits
ADDRESS
7 bits
P
1
ACK
DATA
8 bits
ACK
COMMAND
8 bits
ACK
WR
ADDRESS
7 bits
S
S
ADDRESS
WR
ACK
COMMAND
ACK
S
ADDRESS
7 bits
8 bits
7 bits
RD
ACK
DATA
8 bits
///
P
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6681MEE+ | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6689UP34+ | IC 7CH PREC TEMP MONITOR 20TSSOP |
| MAX6690MEE+ | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6692YMSA+ | IC SENSOR REMOTE SMBUS 8SOIC |
| MAX6693UP9A+T | IC TEMP MONITOR 7CH 20-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6678AEP92+ | 功能描述:板上安裝溫度傳感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6678AEP92+T | 功能描述:板上安裝溫度傳感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6678AEP92-T | 功能描述:板上安裝溫度傳感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6678AEP94 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6678AEP94+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。