- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6659MEE+T (Maxim Integrated)IC TEMP SENSOR SMBUS 16-QSOP Datasheet資料下載
參數資料
| 型號： | MAX6659MEE+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 165K |
| 描述： | IC TEMP SENSOR SMBUS 16-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -55°C ~ 125°C，外部傳感器 |
| 精確度： | ±5°C（最小值） |
| 拓?fù)洌?/td> | ADC，多路復用器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
______________________________________________________________________________________ 13
Status Byte Functions
The status byte (Table 6) indicates which (if any) tem-
perature thresholds have been exceeded. This byte also
indicates whether the ADC is converting and if there is
an open-circuit fault detected with the external sense
junction. After POR, the normal state of the MSB is 1 and
all the other flag bits are 0, assuming no alert or
overtemperature conditions are present. Bits 2 through
6 of the Status register are cleared by any successful
read of the Status register, unless the fault persists. The
ALERT output follows the status flag bit. Both are
cleared when successfully read, but if the condition still
exists, they reassert at the end of the next conversion.
The bits indicating OVERT1 (bits 0 and 1) are cleared
only when the condition no longer exists. Reading the
status byte does not clear the OVERT1 outputs or fault
bits. One way to eliminate the fault condition is for the
measured temperature to drop below the temperature
threshold minus the hysteresis value. Another way to
eliminate the fault condition is by writing new values for
the OVERT1 threshold or hysteresis so that a fault con-
dition is no longer present. Note that the status byte
does not provide status of OVERT2.
The MAX6657/MAX6658/MAX6659 incorporate collision
avoidance so that completely asynchronous operation
is allowed between SMBus operations and temperature
conversions.
When autoconverting, if the T
HIGH
and T
LOW
limits are
close together, its possible for both high-temp and low-
temp status bits to be set, depending on the amount of
time between status read operations. In these circum-
stances, it is best not to rely on the status bits to indi-
cate reversals in long-term temperature changes.
Instead, use a current temperature reading to establish
the trend direction.
Conversion Rate Byte
The Conversion Rate register (Table 7) programs the
time interval between conversions in free-running
autonomous mode (RUN/STOP = 0). This variable rate
BIT
NAME
POR
STATE
FUNCTION
7
(MSB)
MASK1
0
Masks ALERT interrupts if a 1.
6
RUN/STOP
0
Standby mode control bit; if a
1, standby mode is initiated.
5
SPNP
1
Set to 1 when the remote
sensor is a substrate or
common collector PNP. Set to 0
when the remote sensor is a
diode-connected discrete
transistor.
4 to 0
RFU
0
Reserved
Table 5. Configuration-Byte Bit
Assignments
BIT
NAME
POR STATE
FUNCTION
7 (MSB)
BUSY
1
A/D is busy converting when high.
6
LHIGH
0
Internal high-temperature alarm has tripped when high; cleared by POR or readout of
the Status register if the fault condition no longer exists.
5
LLOW
0
Internal low-temperature alarm has tripped when high; cleared by POR or readout of
the Status register if the fault condition no longer exists.
4
RHIGH
0
External high-temperature alarm has tripped when high; cleared by POR or readout of
the Status register if the fault condition no longer exists.
3
RLOW
0
External low-temperature alarm has tripped when high; cleared by POR or readout of
the Status register if the fault condition no longer exists.
2
OPEN
0
A high indicates an external diode open; cleared by POR or readout of the Status
register if the fault condition no longer exists.
1
EOT1
0
A high indicates the external junction temperature exceeds the external OVERT1
threshold.
0
IOT1
0
A high indicates the internal junction temperature exceeds the internal OVERT1
threshold.
Table 6. Status Register Bit Assignments
?癈, SMBus-Compatible Remote/Local Temperature
Sensors with Overtemperature Alarms
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6661AEE+T | IC REG FAN SPEED 16-QSOP |
| MAX6664AEE+T | IC TEMP MON FAN CNTRL 16-QSOP |
| MAX6665ASA45+ | IC FAN CNTRL/DRVR 8-SOIC |
| MAX6670AUB45+ | IC TEMP SENSOR REMOTE 10-UMAX |
| MAX6678AEP92+ | IC TEMP MONITOR 2CH PWM 20-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX665C/D | 功能描述:電荷泵 DICE SALES DICE RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| MAX665C/D+ | 功能描述:電荷泵 RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| MAX665CPA | 功能描述:電荷泵 RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| MAX665CPA+ | 功能描述:直流/直流開關轉換器 8V Switched-Cap Voltage Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX665CWE | 功能描述:電荷泵 8V Switched-Cap Voltage Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。