- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5946LETX+T (Maxim Integrated)IC CNTRLR PCI EXP DL 36TQFN Datasheet資料下載
參數資料
| 型號： | MAX5946LETX+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 17/23頁 |
| 文件大?。?/td> | 1102K |
| 描述： | IC CNTRLR PCI EXP DL 36TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用型，PCI Express? |
| 內部開關： | 無 |
| 電源電壓： | 3.3V，12V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 36-TQFN 裸露焊盤（6x6） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁
FAULT Management
A fault occurs when an overcurrent lasts longer then
t
FAULT
or when the device experiences an overtemper-
ature condition.
" A fault on a main output (12V or 3.3V) shuts down
both main outputs of the respective slot. The 3.3V
auxiliary is not affected.
" A fault on the 3.3V auxiliary output shuts down all
three outputs of the respective slot.
The MAX5946A automatically restarts from a fault shut-
down after the t
RESTART
period, while the MAX5946L
latches off. If an overcurrent fault occurred on a main
output, bring ON_ low for at least t
RESET
(100祍) and
high again to reset the fault and restart the outputs. If
the overcurrent fault occurred on an auxiliary output or
an overtemperature fault occurred, bring both ON_ and
AUXON_ low for a minimum of t
RESET
to reset the fault.
Bring ON_ and/or AUXON_ high again to restart the
respective outputs. As an extra protection, the
MAX5946L waits a minimum of t
RESTART
before it can
be restarted.
Debounced Logic Gate
(Input_ and Output_)
INPUT1 and INPUT2 accept inputs from mechanical
switches. The corresponding outputs are OUTPUT1
and OUTPUT2. OUTPUT_ is debounced for 4ms. When
INPUT_ goes from high to low, OUTPUT_ goes low right
away and stays low for at least 4ms. After the
debounce time OUTPUT_ follows INPUT_. If INPUT_
goes from low to high, OUTPUT_ goes high right away
and stays high for at least 4ms. After the debounce
time, OUTPUT_ follows INPUT_. Figure 5 shows the tim-
ing diagram describing the INPUT_/OUTPUT_
debounced feature.
Present-Detect and Forced-On Inputs
(PPRREESS- -DDEETT__,, FFOON N__)
PRES-DETA and PRES-DETB inputs detect the
PRSNT#2 pin on a PCI express connector. When the
card is plugged in, PRES-DET_ goes low and allows
the turn-on of the outputs of the respective slot after a
4ms debounced time. When the card is removed, an
internal 50k& pullup forces PRES-DET_ high and the
respective slot is shut down with no delay. PRES-DET_
works in conjunction with ON_ and VAUXON_ and only
enables the device when ON_ and VAUXON_ are high.
A logic-low on FON_ forces the respective slot (main
supplies and auxiliary) to turn on regardless of the sta-
tus of the other logic inputs provided the UVLO thresh-
olds are exceeded on all of the inputs.
Active Current Limits
Active current limits are provided for all three outputs of
slot A and slot B. Connect a current-sense resistor
between 12S_+ and 12S_- to set the current limit for the
12V outputs. The current limit is set to 54mV/R
SENSE12
.
R
SENSE12
is either R1 or R3 in the Typical Application
Circuit. Connect a current-sense resistor between
3.3S_+ and 3.3S_- to set the current limit for the 3.3V
main outputs to 20mV/R
SENSE3.3
. R
SENSE3.3
is either R2
or R4 in the Typical Application Circuit. For the auxiliary
output (3.3V
AUXO_
) the current limit is fixed at 470mA.
When the voltage across R
SENSE12
or R
SENSE3.3
reaches the current-limit threshold voltage, the
MAX5946 regulates the gate voltage to maintain the
current-limit threshold voltage across the sense resis-
tor. If the current limit lasts for t
FAULT
then an overcur-
rent fault occurs. The MAX5946_ shuts down both the
12V and 3.3V outputs and asserts the FAULT_ output of
the respective slot.
When the auxiliary output reaches the current limit
(470mA) for longer then t
FAULT
, a fault occurs and the
device shuts down all outputs and asserts FAULT of the
respective slot.
Undervoltage Lockout Threshold
The UVLO thresholds prevent the internal auxiliary
MOSFETs and the external main channel MOSFETs
(Q1Q4 in the Typical Application Circuit) from turning
on if V
12VIN
, V
3.3VIN
, and V
3.3VAUXIN
are not present.
Internal comparators monitor the main supplies and the
auxiliary supply and keep the gate-drive outputs
(12GA, 12GB, 3.3GA, and 3.3GB) low until the supplies
rise above their UVLO threshold. The 12V main supply
is monitored at 12VIN and has a UVLO threshold of
10V. The 3.3V main supply is monitored at 3.3SA+ and
has a UVLO threshold of 2.65V. The auxiliary supply is
monitored at 3.3VAUXIN and has a 2.65V UVLO thresh-
old. For either main channel to operate, V
3.3VAUXIN
must be above its UVLO threshold.
Dual PCI Express, Hot-Plug
Controller
______________________________________________________________________________________ 17
INPUT
DEBOUNCED
OUTPUT
t
DBC
t
DBC
t
DBC
Figure 5. INPUT_ and OUTPUT_ Debounced Feature
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5948BESA+T | IC CNTRLR HOT SWAP 8-SOIC |
| MAX5949BESA+T | IC CNTRLR HOT SWAP 8-SOIC |
| MAX5950ETJ+ | IC PWM CTRL HOT-SW 12V 32TQFN-EP |
| MAX5952CUAX+ | IC PSE CNTRLR FOR POE 36-SSOP |
| MAX5953DUTM+ | IC INTERFACE 802.3AF 48TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5946LEVKIT | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5947AESA | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5947AESA+ | 功能描述:熱插拔功率分布 Positive Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5947AESA+T | 功能描述:熱插拔功率分布 Positive Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5947AESA-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。