- 您現在的位置：買賣IC網 > PDF目錄17047 > MAX5889EVKIT# (Maxim Integrated Products)KIT EVALUATION FOR MAX5889 PDF資料下載
參數資料
| 型號： | MAX5889EVKIT# |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/16頁 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION FOR MAX5889 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| DAC 的數量： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 600M |
| 數據接口： | 并聯 |
| 設置時間： | 11ns |
| DAC 型： | 電流 |
| 工作溫度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX5889 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Applications Information
Clock Interface
To achieve the best possible jitter performance, the
MAX5889 features flexible differential clock inputs
(CLKP, CLKN) that operate from a separate clock
power supply (AVCLK). Use a low-jitter clock to reduce
the DAC’s phase noise and wideband noise. To
achieve the best DAC dynamic performance, the
CLKP/CLKN input source must be designed carefully.
The differential clock (CLKN and CLKP) input can be
driven from a single-ended or a differential clock
source. Use differential clock drive to achieve the best
dynamic performance from the DAC. For single-ended
operation, drive CLKP with a low-noise source and
bypass CLKN to CGND with a 0.1F capacitor.
Figure 4 shows a convenient and quick way of applying
a differential signal created from a single-ended source
using a wideband transformer. Alternatively, drive
CLKP/CLKN from a CMOS-compatible clock source.
Use sine wave or AC-coupled differential ECL/PECL
drive for best dynamic performance.
Differential Output Coupling Using a
Wideband RF Transformer
Use a pair of transformers (Figure 5) or a differential
amplifier configuration to convert the differential voltage
existing between OUTP and OUTN to a single-ended
voltage. Optimize the dynamic performance by using a
differential transformer-coupled output and limit the out-
put power to <0dBm full scale. To achieve the best
dynamic performance, use the differential transformer
configuration. Terminate the DAC as shown in Figure 5,
and use 50 termination at the transformer single-
ended output. This provides double 50 termination for
the DAC output network. With the double-terminated
output and 20mA full-scale current, the DAC produces a
full-scale signal level of approximately -2dBm. Pay close
attention to the transformer core saturation characteris-
tics when selecting a transformer for the MAX5889.
Transformer core saturation can introduce strong 2nd-
order harmonic distortion especially at low output fre-
quencies and high signal amplitudes. For best results,
connect the center tap of the transformer to ground.
When not using a transformer, terminate each DAC out-
put to ground with a 25 resistor. Additionally, place a
50 resistor between the outputs (Figure 6).
For a single-ended unipolar output, select OUTP as the
output and connect OUTN to AGND. Operating the
MAX5889 single-ended is not recommended because
it degrades the dynamic performance.
The distortion performance of the DAC depends on the
load impedance. The MAX5889 is optimized for 50
differential double termination. Using higher termination
impedance degrades distortion performance and
increases output noise voltage.
MAX5889
12-Bit, 600Msps, High-Dynamic-Performance
DAC with LVDS Inputs
______________________________________________________________________________________
11
WIDEBAND RF TRANSFORMER
PERFORMS SINGLE-ENDED-TO-
DIFFERENTIAL CONVERSION
SINGLE-ENDED
CLOCK SOURCE
AGND
1:1
25
CLKP
CLKN
TO DAC
0.1F
Figure 4. Differential Clock-Signal Generation
MAX5889
OUTP
OUTN
WIDEBAND RF TRANSFORMER T2 PERFORMS THE
DIFFERENTIAL-TO-SINGLE-ENDED CONVERSION
T1, 1:1
T2, 1:1
AGND
50
100
50
VOUT, SINGLE-ENDED
D0–D11
LVDS
DATA INPUTS
Figure 5. Differential-to-Single-Ended Conversion Using a Wideband RF Transformer
相關PDF資料 |
PDF描述 |
|---|---|
| UCS2E181MNY9 | CAP ALUM 180UF 250V 20% RADIAL |
| EEC36DRTF | CONN EDGECARD 72POS DIP .100 SLD |
| MAX5535EVKIT+ | KIT EVALUATION FOR MAX5535 |
| MAX5890EVKIT# | KIT EVALUATION FOR MAX5890 |
| MLG1005SR27J | INDUCTOR MULTILAYER 270NH 0402 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5889EVKIT# | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5890EGK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX5890EGK+D | 功能描述:數模轉換器- DAC 14-Bit 600Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5890EGK+TD | 功能描述:數模轉換器- DAC 14-Bit 600Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5890EGK-D | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。