- 您現在的位置：買賣IC網 > PDF目錄10764 > MAX537BCWE (Maxim Integrated Products)IC DAC QUAD CALBRTD 12BIT 16SOIC PDF資料下載
參數資料
| 型號： | MAX537BCWE |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC QUAD CALBRTD 12BIT 16SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 46 |
| 設置時間： | 3µs |
| 位數： | 12 |
| 數據接口： | 串行 |
| 轉換器數目： | 4 |
| 電壓電源： | 雙 ± |
| 功率耗散（最大）： | 762mW |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 管件 |
| 輸出數目和類型： | 4 電壓，單極；4 電壓，雙極 |
| 采樣率（每秒）： | * |
__________Applications Information
Interfacing to the M68HC11*
PORT D of the 68HC11 supports SPI. The four registers
used for SPI operation are the Serial Peripheral Control
Register, the Serial Peripheral Status Register, the Serial
Peripheral Data I/O Register, and PORT D’s Data Direction
Register. These registers have a default starting location of
$1000.
On reset, the PORT D register (memory location $1008) is
cleared and bits 5-0 are configured as general-purpose
inputs. Setting bit 6 (SPE) of the Serial Peripheral Control
Register (SPCR) configures PORT D for SPI as follows:
BIT
7
6543210
NAME
––
SS
SCK
MOSI MISO
TXD
RXD
Bits 6 and 7 are not used. Writes to these bits are ignored.
The PORT D Data Direction Register (DDRD) deter-
mines whether the port bits are inputs or outputs. Its
configuration is shown below:
Setting DDD_ = 0 configures the port bit as an input, while
setting DDD_ = 1 configures the port bit as an output. Writes
to bits 6 and 7 have no effect.
In SPI mode with MSTR = 1, when a PORT D bit is expected
to be an input (SS, MISO, RXD), the corresponding DDRD bit
(DDD_) is ignored. If the bit is expected to be an output
(SCK, MOSI, TXD), the corresponding DDRD bit must be
set for the bit to be an output.
Table 3. Serial Peripheral Status-Register Definitions
MAX536/MAX537
Calibrated, Quad, 12-Bit
Voltage-Output DACs with Serial Interface
18
______________________________________________________________________________________
NAME
SPIE
SPE
MSTR
CPOL
CPHA
SPR1/0
SPR1
SPR0
0
P clock divided by 2
0
1
P clock divided by 4
1
0
P clock divided by 16
1
P clock divided by 32
DEFINITION
When DWOM is set, the six PORT D outputs are open drain. When DWOM is cleared, the outputs are complementary.
Master/Slave select option
Determines the clock phase.
Setting SPE (Serial Peripheral System Enable) configures PORT D for SPI. Clearing SPE configures the port as a general-
purpose I/O port.
Serial Peripheral Interrupt Enable. Clearing SPIE disables the SPI hardware-interrupt request; the SPSR is polled to
determine when an SPI data transfer is complete. Setting SPIE requests a hardware interrupt when the Serial Peripheral
Status Register’s SPIF bit or MODF bit is set.
Determines clock polarity. When set, the serial clock idles high while data is not being transferred; when cleared, the
clock idles low.
Table 2. Serial Peripheral Control-Register Definitions
DWOM
SPI Clock-Rate Select
NAME
DEFINITION
SPIF
SPIF is set when an SPI data transfer is complete. It is cleared by reading the SPSR and then accessing the SPDR.
WCOL
MODF
The Write Collision flag is set when a write to the SPDR occurs while a data transfer is in progress. It is cleared by read-
ing the SPSR and then accessing the SPDR.
The Mode Fault flag detects master/slave conflicts in a multimaster environment. It is set when the “master” controller
has its SS line (PORT D) pulled low, and cleared by reading the SPSR followed by a write to the SPCR.
*M68HC11 is a Motorola microcontroller. General information about the device was obtained from M68HC11 technical manuals.
BIT
7
6543
210
NAME
–
DDD5 DDD4 DDD3 DDD2 DDD1 DDD0
相關PDF資料 |
PDF描述 |
|---|---|
| MAX537BCPE | IC DAC QUAD CALBRTD 12BIT 16-DIP |
| MAX537ACWE | IC DAC QUAD CALBRTD 12BIT 16SOIC |
| MAX536ACPE | IC DAC QUAD CALBRTD 12BIT 16-DIP |
| VI-J6L-MW-F1 | CONVERTER MOD DC/DC 28V 100W |
| MAX5355EUA | IC DAC 3.3V V-OUT 10BIT 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX537BCWE+ | 功能描述:數模轉換器- DAC 12-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX537BCWE+T | 功能描述:數模轉換器- DAC 12-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX537BCWE-T | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX537BEPE | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX537BEPE+ | 功能描述:數模轉換器- DAC 12-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。