- 您現在的位置：買賣IC網 > PDF目錄10845 > MAX5216GUA+ (Maxim Integrated Products)DAC 16BIT SGL BUFFERED LP 8-UMAX PDF資料下載
參數資料
| 型號： | MAX5216GUA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | DAC 16BIT SGL BUFFERED LP 8-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 設置時間： | 14µs |
| 位數： | 16 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 387mW |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
| 輸出數目和類型： | 1 電壓，單極 |
15
Maxim Integrated
14-/16-Bit, Low-Power, Buffered Output,
Rail-to-Rail DACs with SPI Interface
MAX5214/MAX5216
Applications Information
Power-On Reset (POR)
When first power is applied to VDD, the input registers
are set to zero so the DAC output is set to code zero.
To optimize DAC linearity, wait until the supplies have
settled. The MAX5214/MAX5216 output voltage range is
0 to VREF.
Power Supplies and
Bypassing Considerations
Bypass VDD with high-quality 0.1F ceramic capacitors to a
low-impedance ground as close as possible to the device.
Minimize lead lengths to reduce lead inductance.
Connect the GND to the analog ground plane.
Layout Considerations
Digital and AC transient signals on GND can create noise
at the output. Connect GND to the star ground for the
DAC system. Refer the remote DAC loads to this system
ground for the best possible performance. Use proper
grounding techniques, such as a multilayer board with a
low-inductance ground plane, or star connect all ground
return paths back to the MAX5214/MAX5216 GND.
Carefully lay out the traces between channels to reduce
AC cross-coupling. Do not use wire-wrapped boards
and sockets. Use shielding to improve noise immunity.
Do not run analog and digital signals parallel to one
another, especially clock signals. Avoid routing digital
lines underneath the MAX5214/MAX5216 package.
Definitions
Integral Nonlinearity (INL)
INL is the deviation of the measured transfer function
from a straight line drawn between two codes once offset
and gain errors have been nullified.
Differential Nonlinearity (DNL)
DNL is the difference between an actual step height and
the ideal value of 1 LSB. If the magnitude of the DNL is
greater than -1 LSB, the DAC guarantees no missing
codes and is monotonic.
Offset Error
Offset error indicates how well the actual transfer func-
tion matches the ideal transfer function at a single point.
Typically, the point at which the offset error is specified
is at or near the zero-scale point of the transfer function.
Gain Error
Gain error is the difference between the ideal and the
actual full-scale output voltage on the transfer curve,
after nullifying the offset error. This error alters the slope
of the transfer function and corresponds to the same
percentage error in each step.
Settling Time
The settling time is the amount of time required from
the start of a transition, until the DAC output settles to
the new output value within the converter’s specified
accuracy.
Digital Feedthrough
Digital feedthrough is the amount of noise that appears
on the DAC output when the DAC digital control lines
are toggled.
Digital-to-Analog Glitch Impulse
A major carry transition occurs at the midscale point
where the MSB changes from low to high and all other
bits change from high to low, or where the MSB changes
from high to low and all other bits change from low to
high. The duration of the magnitude of the switching
glitch during a major carry transition is referred to as the
digital-to-analog glitch impulse.
Digital-to-Analog Power-Up Glitch Impulse
The digital-to-analog power-up glitch is the duration of
the magnitude of the switching glitch that occurs as the
device exits power-down mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MX7245JP+T | IC DAC 12BIT MULT 28-PLCC |
| VI-2N4-IV-F3 | CONVERTER MOD DC/DC 48V 150W |
| VI-2N4-IV-F2 | CONVERTER MOD DC/DC 48V 150W |
| MAX5884EGM+TD | IC DAC 14BIT 3.3V 200MSPS 48-QFN |
| 2102351-4 | CONN RCPT 8 POS PNL MT PIN KEY A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5216GUA+ | 功能描述:數模轉換器- DAC 16-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5216GUA+T | 功能描述:數模轉換器- DAC 16-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5216LPT# | 制造商:Maxim Integrated Products 功能描述:KIT EVAL FOR MAX5216 |
| MAX5216PMB1# | 功能描述:數據轉換 IC 開發工具 13Bit V-Out DAC w/Config Outs RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX5217BGUA+ | 功能描述:數模轉換器- DAC 16-Bit Low Power Buffered DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。