- 您現在的位置：買賣IC網 > PDF目錄8527 > MAX515ESA+T (Maxim Integrated Products)IC DAC 10BIT VOLT OUT 8-SOIC PDF資料下載
參數資料
| 型號： | MAX515ESA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 10BIT VOLT OUT 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 設置時間： | 25µs |
| 位數： | 10 |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 1 電壓，單極；1 電壓，雙極 |
| 采樣率（每秒）： | * |
MAX504/MAX515
Daisy-Chaining Devices
The serial output, DOUT, allows cascading of two or more
DACs. The data at DIN appears at DOUT, delayed by 16
clock cycles plus one clock width. For low power, DOUT is
a CMOS output that does not require an external pull-up
resistor. DOUT does not go into a high-impedance state
when CS is high. DOUT changes on SCLK’s falling edge
when CS is low. When CS is high, DOUT remains in the
state of the last data bit.
Any number of MAX504/MAX515 DACs can be daisy-
chained by connecting the DOUT of one device to the DIN
of the next device in the chain. For proper timing, ensure
that tCL (SCLK low) is greater than tDO + tDS.
Unipolar Configuration
The MAX504 is configured for a gain of 1 (0V to VREFIN
unipolar output) by connecting BIPOFF and RFB to VOUT
(Figure 6). The converter operates from either single or
dual supplies in this configuration. See Table 1 for the
DAC-latch contents (input) vs. the analog VOUT (output).
In this range, 1LSB = VREFIN (2 -10), where VREF is the
voltage on REFIN.
A gain of 2 (0V to 2VREFIN unipolar output) is set up by
connecting BIPOFF to AGND and RFB to VOUT (Figure
7). Table 2 shows the DAC-latch contents vs. VOUT. The
MAX504 operates from either single or dual supplies in
this mode. In this range,
1LSB = (2)(VREFIN)(2 -10) = (VREFIN)(2 -9).
The MAX515 is internally configured for unipolar gain of
2 operation.
Bipolar Configuration
A bipolar range is set up by connecting BIPOFF to
REFIN and RFB to VOUT, and operating from dual
(±5V) supplies (Figure 8). Table 3 shows the DAC-latch
contents (input) vs. VOUT (output). In this range,
1LSB = VREFIN (2 -9).
Four-Quadrant Multiplication
The MAX504 can be used as a four-quadrant multiplier
by connecting BIPOFF to REFIN and RFB to VOUT, and
using (1) an offset binary digital code, (2) bipolar power
supplies, and (3) a bipolar analog input at REFIN within
the range VSS + 2V to VDD - 2V, as shown in Figure 9.
In general, a 10-bit DAC’s output is (D)(VREFIN)(G),
where “G” is the gain (1 or 2) and “D” is the binary rep-
resentation of the digital input divided by 210 or 1,024.
This formula is precise for unipolar operation. However,
for bipolar, offset binary operation, the MSB is really a
polarity bit. No resolution is lost because the number of
steps is the same. The output voltage, however, has
been shifted from a range of, for example, 0V to 4.096V
(G = 2) to a range of -2.048V to +2.048V.
Keep in mind that when using the DAC as a four-quad-
rant multiplier, the scale is skewed. Negative full scale
is -VREFIN, while positive full scale is +VREFIN - 1LSB.
5V, Low-Power, Voltage-Output,
Serial 10-Bit DACs
10
______________________________________________________________________________________
MAX504
CONNECT BIPOFF
TO VOUT FOR G=1,
TO AGND FOR G=2,
OR TO REFIN FOR
BIPOLAR GAIN
INVERTED
R-2R DAC
DIN
DOUT
SCLK
CS
CLR
2.048V
REFIN
REFOUT
AGND DGND
VDD VSS
33
F
0.1
F
0.1
F
2R
BIPOFF
RFB
VOUT
+5V
0V to -5V
MAX515
INVERTED
R-2R DAC
DIN
DOUT
SCLK
CS
REFIN
AGND
VDD
VOUT
MAX515
ONLY
0.1
F
2R
+5V
Figure 3a. MAX504 Typical Operating Circuit
Figure 3b. MAX515 Typical Operating Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BNW-MU-F2 | CONVERTER MOD DC/DC 5.5V 200W |
| VE-BNW-MU-F1 | CONVERTER MOD DC/DC 5.5V 200W |
| MAX5355CUA+T | IC DAC 10BIT 3.3V VOLT OUT 8UMAX |
| VE-BNV-MU-F3 | CONVERTER MOD DC/DC 5.8V 200W |
| VE-BNV-MU-F2 | CONVERTER MOD DC/DC 5.8V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX516 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述: |
| MAX5160 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Power Digital Potentiometers |
| MAX5160_01 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Power Digital Potentiometers |
| MAX5160LEUA | 功能描述:數字電位計 IC Low-Power Digital Pot RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5160LEUA+ | 功能描述:數字電位計 IC Low-Power Digital Pot RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。