- 您現在的位置：買賣IC網 > PDF目錄11126 > MAX4713EUE+T (Maxim Integrated Products)IC SWITCH QUAD SPST 16TSSOP PDF資料下載
參數資料
| 型號： | MAX4713EUE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH QUAD SPST 16TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 開關 |
| 電路： | 4 x SPST - NC/NO |
| 導通狀態電阻： | 25 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 11 V，±2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
NC_) and COM_ so that signals pass equally well in
either direction.
Positive Fault Condition
When the signal on NO_ (or NC_) exceeds V+ by about
150mV, the high-fault comparator output is high, turn-
ing off FETs N1 and P1. This makes the NO_ (or NC_)
input high impedance regardless of the switch state. If
the switch state is “off”, all FETs are turned off and both
NO_ (or NC_) and COM_ are high impedance. If the
switch state is “on”, clamp FET P2 is turned on, sourc-
ing current from V+ to COM_.
Negative Fault Condition
When the signal on NO_ (or NC_) exceeds V- by about
150mV, the low-fault comparator output is high, turning
off FETs N1 and P1. This makes the NO_ (or NC_) input
high impedance regardless of the switch state. If the
switch state is “off”, all FETs are turned off and both
NO_ (or NC_) and COM_ are high impedance. If the
switch state is “on”, clamp FET N2 is turned on, sinking
current from COM_ to V-.
Transient Fault Response and Recovery
When a fast rise-time or fall-time transient on NC_ or
NO_ exceeds V+ or V-, the output (COM_) follows the
input to the supply rail with only a few nanoseconds
delay. This delay is due to the switch on-resistance and
circuit capacitance to ground. When the input transient
returns to within the supply rails, however, there is a
700ns output recovery delay time. These values
depend on the COM_ output resistance and capaci-
tance, and are not production tested or guaranteed.
The delays are not dependent on the fault amplitude.
Higher COM_ output resistance and capacitance
increase recovery times.
COM_ and IN_ Pins
FETs N2 and P2 can source about ±15mA from V+ or
V- to COM_ in the fault condition. Ensure that if the
COM_ pin is connected to a low-resistance load, the
absolute maximum current rating of 40mA is never
exceeded both in normal and fault conditions.
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
______________________________________________________________________________________
11
V+
NO_
(NC_)
IN_
GND
V-
HIGH
FAULT
LOW
FAULT
ON
N1
P1
P2
COM_
N2
NC SWITCH
-ESD DIODE
NORMALLY OPEN SWITCH CONSTRUCTION
Figure 1. Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4712EUE+T | IC SWITCH QUAD SPST 16TSSOP |
| MAX4711EUE+T | IC SWITCH QUAD SPST 16TSSOP |
| MAX4533CWP+T | IC SWITCH QUAD SPDT 20SOIC |
| DG408DY+T | IC MULTIPLEXER 8X1 16SOIC |
| DG409DY+T | IC MULTIPLEXER DUAL 4X1 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4714ELT+ | 制造商:Maxim Integrated Products 功能描述:0.8-OHM,LOW-VOLTAGE,SINGLE-SUPPLY SPDT ANALOG SWITCH IN SC70 - Rail/Tube |
| MAX4714ELT+T | 功能描述:模擬開關 IC .8Ohm SPDT Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4714ELT-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4714EXT | 制造商:Maxim Integrated Products 功能描述:0.8 OHM, LOW-VOLTAGE, SINGLE-SUPPLY SPST ANAL - Rail/Tube |
| MAX4714EXT+ | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:ANLG SW SGL SPDT 3.6V 6PIN SC-70 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。