- 您現在的位置：買賣IC網 > PDF目錄11126 > MAX4713EUE+T (Maxim Integrated Products)IC SWITCH QUAD SPST 16TSSOP PDF資料下載
參數資料
| 型號： | MAX4713EUE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/17頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH QUAD SPST 16TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 開關 |
| 電路： | 4 x SPST - NC/NO |
| 導通狀態電阻： | 25 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 11 V，±2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
MAX4711/MAX4712/MAX4713
Detailed Description
The MAX4711/MAX4712/MAX4713 differ considerably
from traditional fault-protection switches, with several
advantages. First, they are constructed with two paral-
lel FET’s allowing very low on-resistance. Second, they
allow signals on the NC_ or NO_ pins that are within or
slightly beyond the supply rails to be passed through
the switch to the COM terminal, allowing rail-to-rail sig-
nal operation. Third, when a signal on NC_ or NO_
exceeds the supply rails by about 150mV (a fault con-
dition) the voltage on COM_ is limited to the same
polarity supply voltage. Operation is identical for both
fault polarities.
During a fault condition, the NO_ or NC_ input
becomes high impedance regardless of the switch
state or load resistance. If the switch is on, the COM_
output current is supplied from V+ or V- by the clamp
FET’s that are connected from COM to each supply.
These FET’s can typically source or sink up to 15mA.
When power is removed, the fault protection is still in
effect. In this case, the NO_ or NC_ terminals are a vir-
tual open circuit. The fault can be up to ±12V.
The COM_ pins are not fault-protected, they act as nor-
mal CMOS switch terminals. If a voltage source is con-
nected to any COM_ pin, it should be limited to the
supply voltages. Exceeding the supply voltage will
cause high currents to flow through the ESD-protected
diodes, possibly damaging the device (see Absolute
Maximum Ratings).
Pin Compatibility
These switches have identical pinouts to common non-
fault-protected CMOS switches. Care should be exer-
cised while considering them for direct replacements in
existing printed circuit boards since only the NO_ and
NC_ pins of each switch are fault-protected.
Internal Construction
Internal construction is shown in Figure 1, with the ana-
log signal paths shown in bold. A single NO switch is
shown; the NC configuration is identical except the
logic-level translator is inverting. The analog switch is
formed by the parallel combination of N-channel FET
(N1) and P-channel FET (P1), which are driven on and
off simultaneously according to the input fault condition
and the logic-level state.
Normal Operation
Two comparators continuously compare the voltage on
the NO_ (or NC_) pin with V+ and V-. When the signal
on NO_ or NC_ is between V+ and V- the switch acts
normally, with FETs N1 and P1 turning on and off in
response to IN_ signals. The parallel combination of
N1 and P1 forms a low-value resistor between NO_ (or
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
10
______________________________________________________________________________________
Pin Description
PIN
MAX4711
MAX4712
MAX4713
NAME
FUNCTION
1, 16, 9, 8
IN1, IN2, IN3,
IN4
Logic Inputs. Fault-protected to (V- + 12V).
2, 15, 10, 7
COM1,
COM2,
COM3, COM4
Analog Switch Common Terminals
3, 14, 11, 6
——
NC1, NC2,
NC3, NC4
Fault-Protected Analog Switch Normally Closed Terminals
—
3, 14, 11, 6
—
NO1, NO2,
NO3, NO4
Fault-Protected Analog Switch Normally Open Terminals
——
3, 6
NO1, NO4
Fault-Protected Analog Switch Normally Open Terminals
——
14, 11
NC2, NC3
Fault-Protected Analog Switch Normally Closed Terminals
44
4
V-
Negative Supply Voltage Input. Connect to GND for single-supply
operation.
55
5
GND
Ground
12
N.C.
No Connection. Not internally connected.
13
V+
Positive Supply Input
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4712EUE+T | IC SWITCH QUAD SPST 16TSSOP |
| MAX4711EUE+T | IC SWITCH QUAD SPST 16TSSOP |
| MAX4533CWP+T | IC SWITCH QUAD SPDT 20SOIC |
| DG408DY+T | IC MULTIPLEXER 8X1 16SOIC |
| DG409DY+T | IC MULTIPLEXER DUAL 4X1 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4714ELT+ | 制造商:Maxim Integrated Products 功能描述:0.8-OHM,LOW-VOLTAGE,SINGLE-SUPPLY SPDT ANALOG SWITCH IN SC70 - Rail/Tube |
| MAX4714ELT+T | 功能描述:模擬開關 IC .8Ohm SPDT Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4714ELT-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4714EXT | 制造商:Maxim Integrated Products 功能描述:0.8 OHM, LOW-VOLTAGE, SINGLE-SUPPLY SPST ANAL - Rail/Tube |
| MAX4714EXT+ | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:ANLG SW SGL SPDT 3.6V 6PIN SC-70 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。