- 您現(xiàn)在的位置：買賣IC網 > PDF目錄1937 > MAX15501GTJ+T (Maxim Integrated Products)IC COND ANLG OUTPUT 2.5V 32TQFN PDF資料下載
參數資料
| 型號： | MAX15501GTJ+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 18/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COND ANLG OUTPUT 2.5V 32TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 調節(jié)器 |
| 數據接口： | 串行，SPI? |
| 電壓電源： | 模擬和數字，雙 ± |
| 電源電壓： | ±24V，2.7 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Industrial Analog Current/
Voltage-Output Conditioners
MAX15500/MAX15501
______________________________________________________________________________________ 25
Since the MAX15500/MAX15501 do not use a continuous
clock signal, the SPI read cycles are used to cycle the
error detection and reporting logic. Continue to poll the
device until the error readback reports an all clear status
when resolving single or multiple errors. See below for
examples of typical error handling situations and the
effects of the SPI read operations.
1) Error resolved by the system.
a) The MAX15500/MAX15501 detect an error condi-
tion and ERROR asserts.
b) The host controller reads the error register for the
first time. This has the effect of resetting ERROR.
The data indicates to the host processor which
error is active.
c) The host processor resolves the error successfully.
d) The host processor reads the error register for the
second time. The data still shows that the error is
present as the error persisted for some time after
step b and before step c. If the error is either an
open load or short circuit, the intermittent bit is set.
An overtemperature or a brownout does not set the
intermittent bit. Reading the register a second time
resets the register.
e) The host reads the error register for a third time.
The data now shows the error is resolved and
future occurrences of this error will trigger ERROR
assertion.
2) Error resolved before the host processor reads error
register.
a) The MAX15500/MAX15501 detect an error condi-
tion and ERROR asserts, but the error resolves
itself.
b) The host controller reads the error register for the
first time resetting ERROR. The data indicates to
the host processor which error is active. The data
also indicates to the host that the error has been
resolved since the intermittent bit is set.
c) The host processor reads the error register for the
second time. The data still shows that the error is
active. If the error is for an output fault, the data
also indicates to the host that the error has been
resolved since the intermittent bit is set. Reading
the register a second time resets the register.
3) An error that cannot be resolved.
a) The MAX15500/MAX15501 detect an error condi-
tion and ERROR asserts.
b) The host controller reads the error register for the
first time and resets ERROR. The data indicates to
the host processor which error is active.
c) The host processor takes action to resolve the
error unsuccessfully.
d) The host processor reads the error register for the
second time. The data still shows that the error is
present.
e) The host processor reads the error for the third
time. The data show the error to be unresolved.
ERROR does not respond to the same error until
the error is resolved and reported. ERROR asserts
if different errors occur.
Applications Information
Setting the Output Gain in Current Mode
In current mode, there is approximately 1.0V across the
current-sensing resistors at full scale. The current sens-
ing resistor sets the gain and is calculated as follows:
RSENSE = VSENSE_FS/IMAX
where VSENSE_FS is the full-scale voltage across the
sense resistor.
See Table 8 for values of VSENSE_FS.
Output Gain in Voltage Mode
The output gain in voltage mode is fixed as shown in
Table 9.
Selection of the Compensation
Capacitor (CCOMP)
Use Table 10 to select the compensation capacitor.
Layout Considerations
In the current-mode application, use Kelvin and a short
connection from SENSERN and SENSERP to the RSENSE
terminals to minimize gain-error drift. Balance and mini-
mize all analog input traces for optimum performance.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1558HETB+T | IC CURR-LIM SW DUAL PROG 10-TDFN |
| MAX1563ETC+T | IC CURR-LIM SW SNGL PROG 12-TQFN |
| MAX1564ETE+T | IC TRIPLE USB SW 1.2A 16-TQFN |
| MAX16054AZT+T | IC CTLR ON/OFF W/DEB TSOT23-6 |
| MAX161BEPI+ | IC DAS 8BIT 8-CH 28-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX15511GTL+ | 功能描述:模數轉換器 - ADC New RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX15511GTL+T | 功能描述:模數轉換器 - ADC New RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX15511TGTL+ | 功能描述:模數轉換器 - ADC CPU Controller non-OVP RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX15511TGTL+T | 功能描述:模數轉換器 - ADC CPU Controller non-OVP RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX15513EVI+ | 制造商:Maxim Integrated Products 功能描述:16V INPUT, 8A POINT OF LOAD, QUICKTUNE-PWM BUCK CONVERTER - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC PWM BUCK CONV 16V 28FLIPCHIP |
發(fā)布緊急采購，3分鐘左右您將得到回復。