- 您現在的位置：買賣IC網 > PDF目錄180474 > MAX13362ATL/V+ (MAXIM INTEGRATED PRODUCTS INC) 24-Channel Automotive Switch Monitor; Package: TQFN;40 pin;37 mm² ; Temperature: -40°C to +125°C PDF資料下載
參數資料
| 型號： | MAX13362ATL/V+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 24-Channel Automotive Switch Monitor; Package: TQFN;40 pin;37 mm² ; Temperature: -40°C to +125°C |
| 中文描述： | 24-CHANNEL POWER SUPPLY SUPPORT CKT, QCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, TQFN-40 |
| 文件頁數： | 5/14頁 |
| 文件大?。?/td> | 207K |
| 代理商： | MAX13362ATL/V+ |
Any switch position change (if the switch is interrupt-
enabled) is signaled through the active-low open-drain
INT output. The INT output is cleared when CS goes
low.
Shutdown Mode
In shutdown mode, all switch inputs are high imped-
ance and the external switches are no longer moni-
tored, reducing current consumption on VS to 6A
(typ). The IC resets upon entering shutdown mode and
the contents of the command registers are lost.
Therefore, any setting other than power-on-reset
defaults needs to be reprogrammed after exiting from
the shutdown mode.
Applications Information
Overtemperature Protection
If the IC junction temperature exceeds +165°C, an
interrupt signal is generated and the wetting currents
are disabled to reduce the on-chip power dissipation.
During an overtemperature event, the last switch status
is retained in internal memory and the switch status is
not updated. The interrupt output is cleared when
CS
goes high, but the overtemperature bit T in the output
word remains for as long as the overtemperature condi-
tion persists. When the junction temperature drops by
15°C, the wetting currents are re-enabled and there is a
1ms blanking time before the switches can be polled.
Reverse-Battery Tolerance
The IN0–IN23 switch inputs withstand up to -15V DC
voltage without damage. A reverse-battery diode is
needed to protect VS as shown in the
Typical
Application Circuit.
SD can be controlled from a bat-
tery-level source but should be protected against
reverse battery in the application.
Wetting Current and Power Dissipation
The maximum power dissipation happens when all
switch inputs configured with 15mA continuous wetting
current are all closed. Assuming the battery voltage is
14V, the corresponding power dissipated by the IC is
24 x 14V x 15mA = 5040mW. This exceeds the
absolute maximum power dissipation of 2963mW. In
polling mode, the wetting currents are pulsed at the
programmed polling time to reduce the total power dis-
sipated in the IC.
ISO 7637 Pulse Immunity
VS,
SD, and IN0–IN23 are potentially exposed to ISO
7637 pulses. Bypass VS with a 0.1F and a 47F
capacitor. The VS and
SD voltage must be limited
below 40V during load dump. Bypass IN0–IN23 with at
least 0.047F capacitors at the ECU connector. When
IN0–IN3 or IN23 inputs are used with battery-connected
switches, a 100Ω series resistor is needed. These
external components allow VS,
SD, and IN0–IN23 to
withstand ISO 7637 pulses in the application circuit.
Mechanical Switch Characteristics
The MAX13362 is designed to operate with switches
that have the following characteristics:
1) Minimum resistance value with switch open (due to
leakage): 10kΩ.
2) Maximum resistance value with switch closed:
100Ω.
Chip Information
PROCESS: BiCMOS
MAX13362
24-Channel Automotive Switch Monitor
______________________________________________________________________________________
13
相關PDF資料 |
PDF描述 |
|---|---|
| MAX14752EUE+ | 8-Channel/Dual 4-Channel 72V Analog Mux; Package: TSSOP, 16 pin ; Temperature Range: -40°C to +85°C |
| MAX1549ETL+T | Dual, Interleaved, Fixed-Frequency Step-Down Controller with a Dynamically Adjustable Output |
| MAX1549ETL+ | Dual, Interleaved, Fixed-Frequency Step-Down Controller with a Dynamically Adjustable Output |
| MAX15500GTJ+ | Industrial Analog Current/Voltage Output Conditioners; Package: TQFN;32 pin;26 mm² ; Temperature: -40°C to +105°C |
| MAX15501GTJ+ | Industrial Analog Current/Voltage Output Conditioners; Package: TQFN;32 pin;26 mm² ; Temperature: -40°C to +105°C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13362EVKIT+ | 功能描述:界面開發工具 Evaluation Kit for the MAX13362 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX13366GTE/V+ | 功能描述:板機接口霍耳效應/磁性傳感器 Auto Quad 2-Wire Hall Effect Sw Int RoHS:否 制造商:Honeywell 類型:Bipolar Hall-Effect Digital Position Sensor 工作電源電壓:3 V to 24 V 電源電流:3.5 mA 最大輸出電流:20 mA 工作點最小值/最大值:5 G, 55 G 最小/最大釋放點（Brp）:- 55 G, - 5 G 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 |
| MAX13366GTE/V+T | 功能描述:板機接口霍耳效應/磁性傳感器 Auto Quad 2-Wire Hall Effect Sw Int RoHS:否 制造商:Honeywell 類型:Bipolar Hall-Effect Digital Position Sensor 工作電源電壓:3 V to 24 V 電源電流:3.5 mA 最大輸出電流:20 mA 工作點最小值/最大值:5 G, 55 G 最小/最大釋放點（Brp）:- 55 G, - 5 G 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 |
| MAX1338ETN | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1338ETN+ | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。