- 您現在的位置：買賣IC網 > PDF目錄180474 > MAX13362ATL/V+ (MAXIM INTEGRATED PRODUCTS INC) 24-Channel Automotive Switch Monitor; Package: TQFN;40 pin;37 mm² ; Temperature: -40°C to +125°C PDF資料下載
參數資料
| 型號： | MAX13362ATL/V+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 24-Channel Automotive Switch Monitor; Package: TQFN;40 pin;37 mm² ; Temperature: -40°C to +125°C |
| 中文描述： | 24-CHANNEL POWER SUPPLY SUPPORT CKT, QCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, TQFN-40 |
| 文件頁數： | 4/14頁 |
| 文件大小： | 207K |
| 代理商： | MAX13362ATL/V+ |
MAX13362
IE_: Interrupt Enable
The IE_ bit programs the switch input channel, IN_, to
be interrupt-enabled or interrupt-disabled (0 = interrupt
disabled, 1 = interrupt enabled). The default value after
power-on is 0.
W_.0 and W_.1: Wetting Current
W_.0 and W_.1 bits set the corresponding switch
channel-wetting current as shown in Table 5.
LP: Low Quiescent Current Bit
In polling mode, when
LP is set to 0, the IC is operating
with the lowest quiescent current. The channels that are
not enabled to interrupt have their wetting current dis-
abled and are not monitored. The first pulse of wetting
current after the switch is closed and sampled is 5mA
unless the wetting current for that channel is set to
0mA. The default value of
LP after power-on is 0. When
LP is 1, all channels are monitored and the wetting cur-
rent for each channel is set to the value determined by
W_.0 and W_.1. If the MAX13362 is in continuous
mode,
LP is ignored.
Operating Modes
The MAX13362 features three modes of operation: con-
tinuous mode, polling mode, and shutdown mode. In
continuous mode, the wetting currents (if enabled) are
continuously applied to the closed switches. In polling
mode, the wetting currents are applied to the closed
switches for a preset duration to reduce the power con-
sumption. In shutdown mode, all switch inputs are high
impedance and all circuitry is shutdown.
Continuous Mode Operation (P0–P3 = 0)
In continuous mode, reading of the switch status is initi-
ated by a falling edge on
CS. The microcontroller initi-
ates a low pulse on
CS to update the MAX13362 switch
status register. If
INT remains high, no action needs be
taken by the microcontroller. If
INT goes low, the micro-
controller may perform a read operation to read the
updated switch status. On the rising edge of
CS, INT is
updated. To get correct data, the microcontroller must
wait 10s before initiating a switch status read opera-
tion. (See Figure 4.)
Polling-Mode Operation
In polling mode (see Figure 5), each switch input is
sampled for a programmable polling active time set by
the PA0–PA2 bits between 64s and 4ms (see Table 4).
Sampling is repeated at a period set by the P0–P3 bits
(from 4ms to continuous, see Table 3). All switch inputs
are sampled simultaneously at the end of the polling
active time. Wetting currents (if enabled) are applied to
closed switches during the polling active time.
Therefore, the polling mode reduces the current con-
sumption from the VS power supply to some value
dependent on the polling time chosen.
24-Channel Automotive Switch Monitor
12
______________________________________________________________________________________
*
Default POR value.
Table 5. Wetting Current Setting
W_.1
W_.0
WETTING CURRENT (mA)
00
0*
01
5
10
11
15
CS
INT
SWITCH
STATUS
CHANGE
INT UPDATED, PERFORM READ OPERATION
Figure 4. Continuous Mode Operation
GROUND-CONNECTED
SWITCH-INPUT
INT
SWITCH OPEN
POLLING TIME
SWITCH
POSITION
SAMPLED
SWITCH
POSITION
SAMPLED
POLLING ACTIVE TIME
POLLING
ACTIVE TIME
Figure 5. Switch Sampling in Polling Mode
相關PDF資料 |
PDF描述 |
|---|---|
| MAX14752EUE+ | 8-Channel/Dual 4-Channel 72V Analog Mux; Package: TSSOP, 16 pin ; Temperature Range: -40°C to +85°C |
| MAX1549ETL+T | Dual, Interleaved, Fixed-Frequency Step-Down Controller with a Dynamically Adjustable Output |
| MAX1549ETL+ | Dual, Interleaved, Fixed-Frequency Step-Down Controller with a Dynamically Adjustable Output |
| MAX15500GTJ+ | Industrial Analog Current/Voltage Output Conditioners; Package: TQFN;32 pin;26 mm² ; Temperature: -40°C to +105°C |
| MAX15501GTJ+ | Industrial Analog Current/Voltage Output Conditioners; Package: TQFN;32 pin;26 mm² ; Temperature: -40°C to +105°C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13362EVKIT+ | 功能描述:界面開發工具 Evaluation Kit for the MAX13362 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX13366GTE/V+ | 功能描述:板機接口霍耳效應/磁性傳感器 Auto Quad 2-Wire Hall Effect Sw Int RoHS:否 制造商:Honeywell 類型:Bipolar Hall-Effect Digital Position Sensor 工作電源電壓:3 V to 24 V 電源電流:3.5 mA 最大輸出電流:20 mA 工作點最小值/最大值:5 G, 55 G 最小/最大釋放點（Brp）:- 55 G, - 5 G 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 |
| MAX13366GTE/V+T | 功能描述:板機接口霍耳效應/磁性傳感器 Auto Quad 2-Wire Hall Effect Sw Int RoHS:否 制造商:Honeywell 類型:Bipolar Hall-Effect Digital Position Sensor 工作電源電壓:3 V to 24 V 電源電流:3.5 mA 最大輸出電流:20 mA 工作點最小值/最大值:5 G, 55 G 最小/最大釋放點（Brp）:- 55 G, - 5 G 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 |
| MAX1338ETN | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1338ETN+ | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。