- 您現在的位置：買賣IC網 > PDF目錄9920 > MAX1282BCUE+T (Maxim Integrated Products)IC ADC 12BIT 300KSPS 16-TSSOP PDF資料下載
參數資料
| 型號： | MAX1282BCUE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/23頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 300KSPS 16-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 300k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 13.75mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個偽差分，單極；2 個偽差分，雙極 |
Table 1. Channel Selection in Single-Ended Mode (SGL/
DIF = 1)
Table 2. Channel Selection in Pseudo-Differential Mode (SGL/
DIF = 0)
MAX1282/MAX1283
300ksps/400ksps, Single-Supply, 4-Channel,
Serial 12-Bit ADCs with Internal Reference
12
______________________________________________________________________________________
Track/Hold
The T/H enters its tracking mode on the falling clock
edge after the fifth bit of the 8-bit control word has been
shifted in. It enters its hold mode on the falling clock
edge after the eighth bit of the control word has been
shifted in. If the converter is set up for single-ended
inputs, IN- is connected to COM and the converter
samples the “+” input. If the converter is set up for dif-
ferential inputs, the difference of
[(IN+) - (IN-)] is con-
verted. At the end of the conversion, the positive input
connects back to IN+ and CHOLD charges to the input
signal.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens, and more time must be
allowed between conversions. The acquisition time,
tACQ, is the maximum time the device takes to acquire
the signal and the minimum time needed for the signal
to be acquired. It is calculated by the following equa-
tion:
tACQ = 9 (RS + RIN) 18pF
where RIN = 800 and RS = the source impedance of
the input signal; tACQ is never less than 400ns
(MAX1282) or 625ns (MAX1283). Note that source
impedances below 2k do not significantly affect the
ADC’s AC performance.
Input Bandwidth
The ADC’s input tracking circuitry has a 6MHz
(MAX1282) or 3MHz (MAX1283) small-signal band-
width, so it is possible to digitize high-speed transient
events and measure periodic signals with bandwidths
exceeding the ADC’s sampling rate by using under-
sampling techniques. To avoid high-frequency signals
being aliased into the frequency band of interest, anti-
alias filtering is recommended.
Analog Input Protection
Internal protection diodes, which clamp the analog input
to VDD1 and GND, allow the channel input pins to swing
from GND - 0.3V to VDD1 + 0.3V without damage.
However, for accurate conversions near full scale, the
inputs must not exceed VDD1 by more than 50mV or be
lower than GND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not allow the input current to exceed 2mA.
Starting a Conversion
Start a conversion by clocking a control byte into DIN.
With CS low, each rising edge on SCLK clocks a bit from
DIN into the MAX1282/MAX1283’s internal shift register.
After CS falls, the first arriving logic “1” bit defines the
control byte’s MSB. Until this first “start” bit arrives, any
number of logic “0” bits can be clocked into DIN with no
effect. Table 3 shows the control-byte format.
The MAX1282/MAX1283 are compatible with SPI/
QSPI/MICROWIRE devices. For SPI, select the correct
clock polarity and sampling edge in the SPI control reg-
isters: set CPOL = 0 and CPHA = 0. MICROWIRE, SPI,
and QSPI all transmit a byte and receive a byte at the
same time. Using the Typical Operating Circuit, the sim-
plest software interface requires only three 8-bit transfers
to perform a conversion (one 8-bit transfer to configure
the ADC, and two more 8-bit transfers to clock out the
SEL2
SEL1
SEL0
CH0
CH1
CH2
CH3
COM
00
1
+
–
10
1
+
–
01
0
+
–
11
0
+
–
SEL2
SEL1
SEL0
CH0
CH1
CH2
CH3
00
1
+
–
01
0
+
–
10
1
–
+
11
0
–
+
相關PDF資料 |
PDF描述 |
|---|---|
| ISL32374EIVZ-T | IC XMITTER ESD RS422 LP 16-TSSOP |
| VI-24K-CU-B1 | CONVERTER MOD DC/DC 40V 200W |
| ISL32374EIBZ-T | IC XMITTER ESD RS422 LP 16-SOIC |
| IDT723642L15PF | IC FIFO SYNC 2048X36 120QFP |
| MAX1081ACUP+T | IC ADC 10BIT 300KSPS 20-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1282BEUE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1282BEUE+ | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 400ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1282BEUE+T | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 400ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1282BEUE-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1282EVC16 | 功能描述:數據轉換 IC 開發工具 MAX1282C16 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。