- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX1202BEAP (MAXIM INTEGRATED PRODUCTS INC) 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE PDF資料下載
參數資料
| 型號： | MAX1202BEAP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| 中文描述： | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| 封裝： | 5.30 MM, 0.65 MM PITCH, PLASTIC, SSOP-20 |
| 文件頁數： | 11/24頁 |
| 文件大小： | 309K |
| 代理商： | MAX1202BEAP |
Table 1a. Unipolar Full Scale and Zero
Scale
M
5V, 8-Channel, S erial, 12-Bit ADCs
with 3V Digital Interfac e
______________________________________________________________________________________
11
Input Bandwidth
The ADC’s input tracking circuitry has a 4.5MHz
small-signal bandwidth. Therefore it is possible to digi-
tize high-speed transient events and measure periodic
signals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
high-frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Analog Input Range and Input Protec tion
Internal protection diodes, which clamp the analog
inputs to V
DD
and V
SS
, allow the analog input pins to
swing from (V
SS
- 0.3V) to (V
DD
+ 0.3V) without dam-
age. However, for accurate conversions near full scale,
the inputs must not exceed V
DD
by more than 50mV, or
be lower than V
SS
by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off-channels more than 2mA.
The full-scale input voltage depends on the voltage at
REF (Tables 1a and 1b).
Quic k Look
Use the circuit of Figure 5 to quickly evaluate the
MAX1202/MAX1203’s analog performance. The
MAX1202/MAX1203 require a control byte to be written
to DIN before each conversion. Tying DIN to +3V feeds
in control byte $FF hex, which triggers single-ended
unipolar conversions on CH7 in external clock mode
without powering down between conversions. In exter-
nal clock mode, the SSTRB output pulses high for one
clock period before the most significant bit of the 12-bit
conversion result shifts out of DOUT. Varying the ana-
log input to CH7 alters the sequence of bits from
DOUT. A total of 15 clock cycles per conversion is
required. All SSTRB and DOUT output transitions occur
on SCLK’s falling edge.
How to S tart a Conversion
Clocking a control byte into DIN starts conversion on
the MAX1202/MAX1203. With
CS
low, each rising edge
on SCLK clocks a bit from DIN into the MAX1202/
MAX1203’s internal shift register. After
CS
falls, the first
logic “1” bit defines the control byte’s MSB. Until this
first “start” bit arrives, any number of logic “0” bits can
be clocked into DIN with no effect. Table 2 shows the
control-byte format.
The MAX1202/MAX1203 are fully compatible with
SPI/MICROWIRE devices. For SPI, select the correct
clock polarity and sampling edge in the SPI control reg-
isters: set CPOL = 0 and CPHA = 0. MICROWIRE and
SPI both transmit and receive a byte at the same time.
Using the Typical Operating Circuit the simplest soft-
ware interface requires only three 8-bit transfers to per-
form a conversion (one 8-bit transfer to configure the
ADC, and two more 8-bit transfers to clock out the
12-bit conversion result).
Table 1b. Bipolar Full Scale, Zero Scale,
and Negative Full Scale
REFERENCE
External
ZERO
SCALE
0V
0V
at REFADJ
at REF
FULL SCALE
V
REFADJ
x A*
V
REF
0V
Internal
+4.096V
-1/2 V
REFADJ
x A*
-1/2 V
REF
NEGATIVE
FULL SCALE
-4.096V / 2
+1/2 V
REF
+1/2 V
REFADJ
x A*
0V
0V
+4.096V / 2
FULL SCALE
0V
ZERO
SCALE
at
REFADJ
External
REFERENCE
Internal
at REF
*A = 1.68 for the MAX1202, 1.64 for the MAX1203.
*A = 1.68 for the MAX1202, 1.64 for the MAX1203.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1202BEPP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| MAX1203ACAP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| MAX1203AEPP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| MAX1203BCAP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| MAX1203BEAP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1202BEAP+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202BEAP+T | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202BEAP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202BEPP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202BEPP+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。