- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX1198 (Maxim Integrated Products, Inc.) Dual, 8-Bit, 100Msps, 3.3V, Low-Power ADC with Internal Reference and Parallel Outputs PDF資料下載
參數資料
| 型號： | MAX1198 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual, 8-Bit, 100Msps, 3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| 中文描述： | 雙路、8位、100Msps、3.3V、低功耗ADC，內置電壓基準及并行輸出 |
| 文件頁數： | 19/22頁 |
| 文件大小： | 557K |
| 代理商： | MAX1198 |
physical location of the analog ground (GND) and the
digital output driver ground (OGND) on the ADC
’
s
package. The two ground planes should be joined at a
single point so the noisy digital ground currents do not
interfere with the analog ground plane. The ideal loca-
tion for this connection can be determined experimen-
tally at a point along the gap between the two ground
planes, which produces optimum results. Make this
connection with a low-value, surface-mount resistor (1
to 5
), a ferrite bead, or a direct short.
Alternatively, all ground pins could share the same
ground plane if the ground plane is sufficiently isolated
from any noisy, digital systems ground plane (e.g.,
downstream output buffer or DSP ground plane). Route
high-speed digital signal traces away from the sensitive
analog traces of either channel. Make sure to isolate
the analog input lines to each respective converter to
minimize channel-to-channel crosstalk. Keep all signal
lines short and free of 90
°
turns.
Static Parameter Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-straight-line fit or a line
drawn between the endpoints of the transfer function,
once offset and gain errors have been nullified. The
static linearity parameters for the MAX1198 are mea-
sured using the best-straight-line-fit method.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between
an actual step width and the ideal value of 1LSB. A
DNL error specification of less than 1LSB guarantees
no missing codes and a monotonic transfer function.
Dynamic Parameter Definitions
Aperture Jitter
Figure 11 depicts the aperture jitter (t
AJ
), which is the
sample-to-sample variation in the aperture delay.
Aperture Delay
Aperture delay (t
AD
) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 11).
Signal-to-Noise Ratio
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantiza-
tion error only and results directly from the ADC
’
s reso-
lution (N-bits):
SNR
dB[max]
= 6.02
dB
N + 1.76
dB
M
Dual, 8-Bit, 100Msps, 3.3V, Low-Power ADC
with Internal Reference and Parallel Outputs
______________________________________________________________________________________
19
0
°
90
°
÷
8
DOWNCONVERTER
MAX2451
INA+
INA-
MAX1198
INB+
INB-
DSP
POST-
PROCESSING
Figure 10. Typical QAM Application Using the MAX1198
HOLD
ANALOG
INPUT
SAMPLED
DATA (T/H)
T/H
t
AD
t
AJ
TRACK
TRACK
CLK
Figure 11. T/H Aperture Timing
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1198ECM | Dual, 8-Bit, 100Msps, 3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1200 | +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc |
| MAX1200AEMH | +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc |
| MAX1200BCMH | +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc |
| MAX1200ACMH | RB Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 24V; Output Voltage (Vdc): 05V; Power: 1W; Low Cost 1W Converter; Power Sharing on Dual Output Version; Industry Standard Pinout; 1kVDC & 2kVDC Isolation Options; Optional Continuous Short Circuit Protected; UL94V-0 Package Material; Efficiency to 85% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1198E/D | 功能描述:模數轉換器 - ADC DICE SALES DICE RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1198ECM+D | 功能描述:模數轉換器 - ADC 8-Bit 2Ch 100Msps 3.3V High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1198ECM+TD | 功能描述:模數轉換器 - ADC 8-Bit 2Ch 100Msps 3.3V High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1198ECM-D | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1198ECM-TD | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。