- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX1180 (Maxim Integrated Products, Inc.) Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC with Internal Reference and Parallel Outputs PDF資料下載
參數資料
| 型號： | MAX1180 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| 中文描述： | 雙路、10位、105Msps、3.3V、低功耗ADC，內置電壓基準及并行輸出 |
| 文件頁數： | 18/20頁 |
| 文件大?。?/td> | 573K |
| 代理商： | MAX1180 |
minimize channel-to-channel crosstalk. Keep all signal
lines short and free of 90 degree turns.
Static Parameter Definitions
Integral Nonlinearity (INL)
Integral nonlinearity is the deviation of the values on an
actual transfer function from a straight line. This straight
line can be either a best straight-line fit or a line drawn
between the endpoints of the transfer function, once
offset and gain errors have been nullified. The static lin-
earity parameters for the MAX1180 are measured using
the best straight-line fit method.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between an
actual step-width and the ideal value of 1LSB. A DNL
error specification of less than 1LSB guarantees no
missing codes and a monotonic transfer function.
Dynamic Parameter Definitions
Aperture Jitter
Figure 9 depicts the aperture jitter (t
AJ
), which is the
sample-to-sample variation in the aperture delay.
Aperture Delay
Aperture delay (t
AD
) is the time defined between the
falling edge of the sampling clock and the instant when
an actual sample is taken (Figure 9).
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error).
The ideal, theoretical minimum analog-to-digital noise is
caused by quantization error only and results directly
from the ADCs resolution (N-Bits):
SNR
dB[max]
= 6.02
dB
N + 1.76
dB
In reality, there are other noise sources besides quanti-
zation noise; thermal noise, reference noise, clock jitter,
etc. SNR is computed by taking the ratio of the RMS
signal to the RMS noise, which includes all spectral
components minus the fundamental, the first five har-
monics, and the DC offset.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to all spectral components minus the fundamental
and the DC offset.
Effective Number of Bits (ENOB)
ENOB specifies the dynamic performance of an ADC at
a specific input frequency and sampling rate. An ideal
ADC
’
s error consists of quantization noise only. ENOB
is computed from:
Total Harmonic Distortion (THD)
THD is typically the ratio of the RMS sum of the first four
harmonics of the input signal to the fundamental itself.
This is expressed as:
where V
1
is the fundamental amplitude, and V
2
through
V
5
are the amplitudes of the 2nd- through 5th-order
harmonics.
Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio expressed in decibels of the RMS
amplitude of the fundamental (maximum signal compo-
nent) to the RMS value of the next largest spurious
component, excluding DC offset.
THD
V
V
V
V
V
=
×
+
+
+
20
10
2
2
2
2
1
2
3
4
5
log
ENOB
SINAD
dB
dB
dB
=
1 76
.
6 02
.
M
Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC
with Internal Reference and Parallel Outputs
18
______________________________________________________________________________________
HOLD
ANALOG
INPUT
SAMPLED
DATA (T/H)
T/H
t
AD
t
AJ
TRACK
TRACK
CLK
Figure 9. T/H Aperture Timing
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1180ECM | Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1182 | Dual 10-Bit, 65Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1183 | Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1183ECM | Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1185 | Dual 10-Bit, 20Msps, +3V, Low-Power ADC with Internal Reference and Multiplexed Parallel Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11800ETC/V+ | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC/V+T | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC+ | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC+T | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800EVKIT+ | 功能描述:顯示開發工具 MAX11800 Eval Kit RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V |
發布緊急采購，3分鐘左右您將得到回復。